1、Designation:D476119Standard Test Methods forMechanical Properties of Lumber and Wood-BasedStructural Materials1This standard is issued under the fixed designation D4761;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last
2、 revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.INTRODUCTIONNumerous evaluations of the mechanical properties of wood-based structural materials have beensatisfactorily conducted since t
3、he late 1920s,using Test Methods D198.Those methods are best suitedto a laboratory environment and are adaptable to a variety of products such as stress-graded lumber,sawn timber,laminated timbers,wood-plywood composite members,reinforced and pre-stressedtimbers.The procedures presented in these tes
4、t methods have been derived from those set forth in TestMethods D198.They are intended primarily for application to stress-graded lumber,but can be usedfor other wood-based structural materials as well.The procedures are more flexible than those in TestMethods D198,making testing in a non-laboratory
5、 environment more feasible.Thus the test methodscan be used on production sites for field testing and quality control,as well as in laboratories forresearch applications.Key differences from Test Methods D198 are the testing speed,the deflection-measuring procedures for specimens under load,and the
6、detail of data reporting.Furthermore,the testmethods do not require that specimens be loaded to failure.Since these test methods allow latitude in testing procedures,the procedures used shall be fullydocumented in the test report.It may also be desirable to correlate the results from tests carried o
7、utaccording to these test methods with test results obtained using a traditional procedure,such as thatset forth in Test Methods D198.1.Scope1.1 These test methods cover the determination of themechanical properties of stress-graded lumber and other wood-based structural materials.1.2 These test met
8、hods appear in the following order:SectionBending edge-wise6Bending flat-wise:Center-point loading7Third-point loading8Axial strength in tension9Axial strength in compression101.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibili
9、ty of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization esta
10、blished in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D9 Terminology Relating to Wood and Wood-Based Prod-uctsD198 Test
11、Methods of Static Tests of Lumber in StructuralSizesD2915 Practice for Sampling and Data-Analysis for Struc-tural Wood and Wood-Based ProductsD4442 Test Methods for Direct Moisture Content Measure-ment of Wood and Wood-Based Materials1These test methods are under the jurisdiction of ASTM Committee D
12、07 onWood and are the direct responsibility of Subcommittee D07.01 on FundamentalTest Methods and Properties.Current edition approved April 1,2019.Published May 2019.Originallyapproved in 1988.Last previous edition approved in 2018 as D4761 18.DOI:10.1520/D4761-19.2For referenced ASTM standards,visi
13、t the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United
14、 StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to
15、 Trade(TBT)Committee.1 D7438 Practice for Field Calibration and Application ofHand-Held Moisture MetersE4 Practices for Force Verification of Testing MachinesE6 Terminology Relating to Methods of Mechanical TestingE177 Practice for Use of the Terms Precision and Bias inASTM Test Methods2.2 Other Doc
16、ument:3NIST Voluntary Product Standard PS20 American SoftwoodLumber StandardNOTE1The current version of PS20 is given as an example of aproduct standard applicable to stress-graded lumber.Other product stan-dards may apply to stress-graded lumber.For wood-based structuralmaterials other than stress-graded lumber,relevant product standards mayapply.3.Terminology3.1 DefinitionsSee Terminologies D9 and E6 and Prac-tices E4 and E177 for definitions of terms used in these testmethods.3.2 Definitions