1、Designation:D515898(Reapproved 2019)Standard Test Method forDetermination of Particle Size of Powdered ActivatedCarbon by Air-Jet Sieving1This standard is issued under the fixed designation D5158;the number immediately following the designation indicates the year oforiginal adoption or,in the case o
2、f revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the particlesize of powdered activated carbons using an
3、 air-jet sievedevice.For purposes of this test method,powdered activatedcarbon is defined as activated carbon in particle sizes predomi-nantly smaller than 80 mesh.1.2 The values stated in SI units are to be regarded as thestandard.The inch-pound units given in parentheses are forinformation only.1.
4、3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 Th
5、is international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(
6、TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D2652 Terminology Relating to Activated CarbonE11 Specification for Woven Wire Test Sieve Cloth and TestSievesE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE300 Practice for Sampling Industrial ChemicalsE691 Practice
7、for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3.Terminology3.1 DefinitionsTerms relating to this test method aredefined in Terminology D2652.4.Summary of Test Method4.1 A weighed sample of as-received powdered activatedcarbon is placed in a test sieve that is inse
8、rted in the sieveholder of the air-jet sieve assembly.Air is passed through thesieve from a slowly rotating nozzle to fluidize the sample for agiven period of time.Exit airflow removes undersized particlesdownward through the test sieve to a collection canister.Theamount of carbon retained on the te
9、st sieve is weighed and thepercent passing the test sieve is computed by difference.For aparticle size distribution,the test must be repeated using sieveswith different openings.5.Significance and Use5.1 The particle size of powdered activated carbon issometimes used to evaluate filter cake filtrati
10、on rates and thefilter penetration in filtering applications.The selection andhandling of powdered activated carbon,and operation ofprocesses using powdered activated carbon,requires theknowledge of the particle size.NOTE1Relative humidity(RH)can affect the repeatability andaccuracy of this test.Act
11、ivated carbon not at equilibrium with the RH ofthe ambient air may lose or gain weight accordingly,dependent uponwhether or not the carbon picks up or loses moisture.6.Apparatus6.1 Air-Jet Sieve Assembly.6.2 Wire Cloth Sieves,bronze or stainless steel(stainlesssteel sieves preferred),200 and 325 mes
12、h,in accordance withSpecification E11.The sieves shall be 203 mm(8 in.)indiameter.6.3 Brush,soft bristle.6.4 Balance,with a sensitivity of 1.0 mg.6.5 Ultrasonic Bath,capable of cleaning 203-mm(8-in.)diameter sieves.7.Sampling7.1 Activated carbon is not strictly a chemically and physi-cally homogeneo
13、us material.To enable performing meaningful1This test method is under the jurisdiction of ASTM Committee D28 onActivated Carbon and is the direct responsibility of Subcommittee D28.02 on LiquidPhase Evaluation.Current edition approved Aug.1,2019.Published August 2019.Originallyapproved in 1991.Last
14、previous edition approved in 2013 as D5158 98(2013).DOI:10.1520/D5158-98R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe AST
15、M website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of
16、International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 tests within the stated tolerances of the ASTM test methods,itis essential that sampling be performed to obtain as represen-tative a sample as possible.When a small amount of samplerepresents tons of material,the collection,mixing,and prepa-ration of samples is extremely important.The practice de-scribed in Practice E300 is suitable to ensure that sampling andsamp