1、Designation:D513320aStandard Test Method forLow Temperature,Low Shear Rate,Viscosity/TemperatureDependence of Lubricating Oils Using a Temperature-Scanning Technique1This standard is issued under the fixed designation D5133;the number immediately following the designation indicates the year oforigin
2、al adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the measurement of the appar-ent viscosity of e
3、ngine oil at low temperatures.1.2 A shear rate of approximately 0.2 s-1is produced atshear stresses below 100 Pa.Apparent viscosity is measuredcontinuously as the sample is cooled at a rate of 1 C h overthe range 5 C to 40 C,or to the temperature at which theviscosity exceeds 40 000 mPas(cP).1.3 The
4、 measurements resulting from this test method areviscosity,the maximum rate of viscosity increase(GelationIndex),and the temperature at which the Gelation Indexoccurs.1.4 Applicability to petroleum products other than engineoils has not been determined in preparing this test method.1.5 The values st
5、ated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,healt
6、h,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of Internatio
7、nal Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D341 Practice for Viscosity-Temperature Equations andCharts for Liquid Petroleum or Hydrocarbon ProductsD3829 Test Method for Predicting
8、 the Borderline PumpingTemperature of Engine OilD4684 Test Method for Determination of Yield Stress andApparent Viscosity of Engine Oils at Low TemperatureD6299 Practice for Applying Statistical Quality Assuranceand Control Charting Techniques to Evaluate AnalyticalMeasurement System PerformanceD796
9、2 Practice for Determination of Minimum ImmersionDepth and Assessment of Temperature Sensor Measure-ment DriftE644 Test Methods for Testing Industrial Resistance Ther-mometers3.Terminology3.1 Definitions:3.1.1 apparent viscosity,nthe viscosity obtained by use ofthis test method.3.1.1.1 DiscussionSee
10、 3.1.7 for definition of viscosity andunits.3.1.2 digital contact thermometer(DCT),nan electronicdevice consisting of a digital display and associated tempera-ture sensing probe.3.1.2.1 DiscussionThis device consists of a temperaturesensor connected to a measuring instrument;this instrumentmeasures
11、the temperature-dependent quantity of the sensor,computes the temperature from the measured quantity,andprovides a digital output.This digital output goes to a digitaldisplay or recording device,or both,that may be internal orexternal to the device.1This test method is under the jurisdiction of ASTM
12、 Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.07 on Flow Properties.Current edition approved June 1,2020.Published June 2020.Originallyapproved in 1990.Last previous edition approved in 2020 as D5133 20.DOI:10.1520/D5133-20A.2For
13、referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyri
14、ght ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International St
15、andards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.3.1.2.2 DiscussionThe devices are often referred to as“digital thermometers,”however the term includes devices thatsense temperature by means other than being in physicalcontact with t
16、he media.3.1.2.3 DiscussionPET is an acronym for portable elec-tronic thermometers,a subset of digital contact thermometers(DCT).3.1.3 Newtonian oil,nan oil or fluid that at a giventemperature exhibits a constant viscosity at all shear rates orshear stresses.3.1.4 non-Newtonian oil,nan oil or fluid that at a giventemperature exhibits a viscosity that varies with changing shearstress or shear rate.3.1.5 shear rate,nvelocity gradient perpendicular to thedirection of flow.3.1.5.1 DiscussionThe SI u