1、Designation:D4869/D4869M15Standard Specification forAsphalt-Saturated Organic Felt Underlayment Used in SteepSlope Roofing1This standard is issued under the fixed designation D4869/D4869M;the number immediately following the designation indicates theyear of original adoption or,in the case of revisi
2、on,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers asphalt-saturated organic feltfor use as an underlayment with steep slope roofing.
3、1.2 The objective of this specification is to provide afinished product that will lie flat and resist wrinkling,puckering,and shrinking when left exposed to the sun,rain,frost,or dew for a period of two weeks after application.1.3 The values stated in either SI units or inch-pound unitsare to be reg
4、arded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.4 The following safety hazards caveat pertains only to thetest
5、 method portion,Section 8,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory li
6、mita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2D70 Test Method for Density of Semi-Solid BituminousMaterials(Pycnometer Method)D146 Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing andWaterproofingD228 Test Methods for Sampling,Testing,an
7、d Analysis ofAsphalt Roll Roofing,Cap Sheets,and Shingles Used inRoofing and WaterproofingD1079 Terminology Relating to Roofing and WaterproofingD1922 Test Method for Propagation Tear Resistance ofPlastic Film and Thin Sheeting by Pendulum MethodD6136 Test Method for Kerosine Number of Unsaturated(D
8、ry)Felt by Vacuum MethodF1087 Test Method for Linear Dimensional Stability of aGasket Material to Moisture3.Terminology3.1 DefinitionsFor definitions of terms used in thisspecification,refer to Terminology D1079.4.Classification4.1 Asphalt-saturated felts covered by this specification areof four typ
9、es:4.1.1 Type I#8 Underlayment,4.1.2 Type II#13 Underlayment,4.1.3 Type III#20 Underlayment,and4.1.4 Type IV#26 Underlayment.5.Materials and Manufacture5.1 In the process of manufacture,a single thickness oforganic dry felt shall be uniformly saturated with an asphalticsaturant.5.2 The felt shall be
10、 produced principally from organicfibers.The surface of the felt shall be uniform and relativelysmooth.Upon splitting or tearing on the bias,the felt shallappear free of lumps or particles of foreign substances.6.Physical Requirements6.1 The material shall conform to the physical requirementsin acco
11、rdance with Table 1 and the dimensions and masses inaccordance with Table 2.6.2 The finished product shall not crack nor be so sticky asto cause tearing or other damage upon being unrolled attemperatures between 0 and 60C 32 and 140F.6.3 The finished product shall pass the water shower expo-sure tes
12、t in accordance with 8.6,indicating resistance to liquidwater transmission.7.Workmanship,Finish,and Appearance7.1 The felt shall be thoroughly and uniformly saturated,and shall show no unsaturated spots at any point upon cutting1This specification is under the jurisdiction of ASTM Committee D08 onRo
13、ofing and Waterproofing and is the direct responsibility of Subcommittee D08.02on Steep Roofing Products and Assemblies.Current edition approved Jan.1,2015.Published February 2015.Originallyapproved in 2002.Last previous edition approved in 2011 as D4869 05(2011)1.DOI:10.1520/D4869_D4869M-15.2For re
14、ferenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Consh
15、ohocken,PA 19428-2959.United States1 50-mm 2-in.wide strips at random across the entire sheet andsplitting them open for their full length.7.2 The saturated felt may be surfaced lightly on one sidewith talc or other finely comminuted mineral material toprevent sticking in the roll.7.3 The finished m
16、aterial shall be free of visible externaldefects,such as holes,ragged or untrue edges,breaks,cracks,tears,protuberances,and indentations.8.Sampling and Test Methods8.1 Sample the material in accordance with Test MethodD146 and determine the properties enumerated in this specifi-cation in accordance with Test Methods D146,D228,D1922,D6136,and F1087 as specified below.8.2 Determine the saturation percent of the felt in accor-dance with Test Method D146,Section 19(BituminousSaturant),and the satura