1、Designation:D496907(Reapproved 2012)Standard Specification forPolytetrafluoroethylene(PTFE)Coated Glass Fabric1This standard is issued under the fixed designation D4969;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last
2、 revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers glass fabric impregnated,coated,and sintered on both sides with PTFE to a nominalthickness of 0.318
3、mm(0.015 in.)or less.1.2 The PTFE-coated glass fabric is for electrical,chemical,and mechanical uses.1.3 The PTFE-coated glass fabric of this specification doesnot pertain to structural fabric,single-sided PTFE coatings,ormaterials used for laminates.1.4 The values stated in SI units as detailed in
4、IEEE/ASTMSI-10.NOTE1There is no ISO standard that covers information included inthis specification.The dielectric test is mentioned in ISO 12086-2 andISO 130001 and 2.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD149 Test Method for Dielectric Breakdown Voltage andD
5、ielectric Strength of Solid Electrical Insulating Materialsat Commercial Power FrequenciesD257 Test Methods for DC Resistance or Conductance ofInsulating MaterialsD374 Test Methods for Thickness of Solid Electrical Insu-lationD579 Specification for Greige Woven Glass FabricsD618 Practice for Conditi
6、oning Plastics for TestingD737 Test Method for Air Permeability of Textile FabricsD751 Test Methods for Coated FabricsD883 Terminology Relating to PlasticsD902 Test Methods for Flexible Resin-Coated Glass Fabricsand Glass Fabric Tapes Used for Electrical InsulationD1424 Test Method for Tearing Stren
7、gth of Fabrics byFalling-Pendulum(Elmendorf-Type)ApparatusD3892 Practice for Packaging/Packing of PlasticsD4441 Specification for Aqueous Dispersions of Polytetra-fluoroethyleneIEEE/ASTM SI-10 Standard for Use of the InternationalSystem of Units(SI):The Modern Metric System2.2 ISO Standard:3ISO 1208
8、6-2 PlasticsFluoropolymer Dispersions andMoulding and Extrusion MaterialsPart 2:Preparation ofTest Specimens and Determination of PropertiesISO 130001and2 PlasticsPolytetrafluoroethylene(PTFE)Semi-Finished Products3.Terminology3.1 Definitions:3.1.1 Definitions of terms relating to plastics used in t
9、hisspecification shall be in accordance with Definitions D883.Definitions of terms relating to textiles used in this specifica-tion shall be in accordance with Terminology D123.3.1.2 structural fabricPTFE-coated fabric to a thicknessof greater than 0.381 mm(0.015 in.).3.1.3 lot,none production run o
10、r a uniform blend of twoor more production runs.4.Classification4.1 There shall be six types of PTFE-coated glass fabrics asdescribed in Table 1.4.2 Use a one-line system to specify materials covered bythis specification.The system uses redefined cells to refer tospecific aspects of this specificati
11、on,as illustrated below asfollows.SpecificationStandard NumberBlockTypeGradeClassSpecialNotesExample:ASTM D4969-XXIV,For this example,the line call out would be:ASTMD4969 XX,IV ,Porosity 1530 CFM,and would specifya Type IV porous product which is referenced in Table 1 withno grade or class since the
12、se subcategories do not appear in thisspecification.A comma is used as the separator between thestandard number and the type.Separators are not needed1This specification is under the jurisdiction of Committee D20 on Plastics and isthe direct responsibility of Subcommittee D20.15 on Thermoplastic Mat
13、erials.Current edition approved April 1,2012.Published June 2012.Originallyapproved in 1989.Last previous edition approved in 2007 as D4969 07.DOI:10.1520/D4969-07R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book
14、 of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.*A Summary of Changes section appears at the end of this standardCopyright AST
15、M International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 between the type,grade,and class because they are,in turn,Roman numerals,Arabic digits,and uppercase letters,asprovided in Section B8 of Form and Style for ASTM Standards.Provision for“Special Notes”is i
16、ncluded so that other infor-mation can be provided when required.An example would bein this specification where porosity would be defined as 1530CFM.When special notes are used,they should be preceded bya comma.5.Materials and Manufacture5.1 Glass FabricThe base material used in the manufac-ture of the products of this specification shall be a woven glassfabric produced in accordance with Specification D579.Aguideline for generally acceptable substrate fabrics for thecommon thickness of PTFE/gla