ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:65.47KB ,
资源ID:177715      下载积分:13 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/177715.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_4921_-_20.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_4921_-_20.pdf

1、Designation:D492120Standard Test Method forFoaming Tendencies of Engine Coolants at RoomTemperature1This standard is issued under the fixed designation D4921;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A

2、 number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method applies to a simple shake test forevaluating the tendency of an aqueous solution of enginecoolant to foam at room tempera

3、ture.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish app

4、ro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDev

5、elopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1176 Practice for Sampling and Preparing Aqueous Solu-tions of Engine Coolants orAntirusts for Testing Purposes3.

6、Summary of Test Method3.1 A 30%by volume coolant concentrate solution isprepared in deionized water and shaken in a stoppered gradu-ated cylinder for 30 s.The volume of foam formed in thecylinder is read in millilitres.Preparation of the sample is donein accordance with Practice D1176.4.Significance

7、 and Use4.1 The test method will generally identify coolants thathave a tendency to foam excessively at room temperature.NOTE1In use,the foaming tendency of a coolant solution may beincreased by service aging or contamination.5.Apparatus5.1 Graduated Cylinders100 mLgraduated cylinders withplastic st

8、oppers are preferred for ease of handling.5.2 Water BathA water bath or equivalent device capableof maintaining temperature at 22.5 C 6 2.5 C.6.Reagents6.1 Deionized Water.7.Test Conditions7.1 Test TemperatureThe test solution shall be maintainedat 22.5 C 6 2.5 C for 30 min before shaking.7.2 Shake

9、RateThe graduated cylinder containing the testsolution should be shaken vigorously for 30 s before a readingof the foam volume is taken.7.3 Number of TestsEach test solution should be tested intriplicate,using a freshly prepared test solution for each test.8.Test Procedure8.1 Prepare three 50 mL sam

10、ples of a 30%by volume(15 mL)coolant solution in deionized water.Use 100 mLgraduated cylinders.8.2 The graduated cylinders should be stoppered and placedin the constant 22.5 C 6 2.5 C temperature water bath.Ensure that the test solution is submerged below the waterlevel.Allow the test solutions to e

11、quilibrate in the bath for 30min.8.3 Remove the graduated cylinder from the bath and shakevigorously(using forearm),making a 90 arc for approxi-mately 30 s(use a stopwatch or timing device).To avoidleakage of test contents from the cylinder,the stopper shouldbe held or locked in place.NOTE2Secure th

12、e stopper on the graduated cylinder using thumb,index finger,or suitable locking device.1This test method is under the jurisdiction of ASTM Committee D15 on EngineCoolants and Related Fluids and is the direct responsibility of SubcommitteeD15.06 on Glassware Performance Tests.Current edition approve

13、d April 1,2020.Published April 2020.Originallyapproved in 1989.Last previous edition approved in 2012 as D492195(2012).DOI:10.1520/D492120.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume inf

14、ormation,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization e

15、stablished in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.8.4 Place cylinder on a level surface and allow it to standundisturbed for 10 s.8.5 Record the foam volum

16、e to the nearest millilitre byreading the top level of foam and subtracting 50 mL to accountfor the liquid level.9.Report9.1 Report foam volumes(to the nearest 1.0 mL)for eachtest as well as the average of the tests.10.Precision and Bias10.1 Precision:10.1.1 Repeatability of the results within a given laboratoryis normally within 15%of the mean.10.1.2 Reproducibility among different laboratories is nor-mally within 30%of the mean.10.2 BiasSince there is no accepted reference materialsuitable for

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2