1、Designation:D523213Standard Test Method forDetermining the Stability and Miscibility of a Solid,Semi-Solid,or Liquid Waste Material1This standard is issued under the fixed designation D5232;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revi
2、sion,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method is designed to determine whether awaste material reacts when it is mixed with air,water,s
3、trongacid,strong base,an oil/solvent mixture,other waste mixtures,or solid media such as a geological formation or solidificationagents.1.2 The miscibility of the waste material with the abovemedia can also be defined.NOTE1The following ASTM standards provide supplemental infor-mation:Test Methods D
4、4978,D4979,D4980,D4981,D4982,D5049,D5057,and D5058.1.3 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility
5、 of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.For specific hazardstatements,see Section 8.2.Referenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent WaterD4978 Test Methods fo
6、r Screening of Reactive Sulfides inWasteD4979 Test Method for Physical Description ScreeningAnalysis in WasteD4980 Test Methods for Screening of pH in Waste(With-drawn 2009)3D4981 Test Method for Screening of Oxidizers in WasteD4982 Test Methods for Flammability Potential ScreeningAnalysis of WasteD
7、5049 Test Method for Screening Cyanides In Waste(With-drawn 1999)3D5057 Test Method for ScreeningApparent Specific Gravityand Bulk Density of WasteD5058 Practices for Compatibility of Screening Analysis ofWasteD5681 Terminology for Waste and Waste Management3.Terminology3.1 Definitions of terms in t
8、his test method appear inTerminology D5681.4.Summary of Test Method4.1 The stability and miscibility of a waste material areobserved when the waste is mixed with various media.5.Significance and Use5.1 This test method will identify waste materials that arepotentially unstable when they come in cont
9、act with othermaterials at a waste treatment or disposal site.5.2 This test method will serve to determine the miscibilityof waste materials with various media,including other wastes.5.3 This test method may not be applicable to all wastes.The appropriateness of these tests depends upon the proposed
10、management of the waste.5.4 Since the initiation of some chemical reactions are slowto take place,the user may wish to establish reagent-to-wastecontact times prior to observing the mixes for any reactions.6.Apparatus and Materials6.1 Disposable Cups,minimum 40-mL total volume.Selectplastics or othe
11、r materials compatible with the reagents in-volved.6.2 Stirring Rods,Spatulas,Disposal Droppers,WatchGlasses,and so forth.6.3 Other waste materials to be evaluated with the testsample.1This test method is under the jurisdiction of ASTM Committee D34 on WasteManagement and is the direct responsibilit
12、y of Subcommittee D34.01.06 onAnalytical Methods.Current edition approved April 1,2013.Published May 2013.Originallyapproved in 1992.Last previous edition approved in 2008 as D5232 92(2008).DOI:10.1520/D5232-13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Custome
13、r Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Con
14、shohocken,PA 19428-2959.United States1 6.4 Solid Media,to be evaluated with the test sample.7.Reagents7.1 Purity of WaterThe deionized water used to preparethe aqueous test solutions should conform to the conductivityspecifications ofASTM Type II water as found in SpecificationD1193.7.2 Hydrochloric
15、 Acid(HCl)Test Solution,carefully mix100 g of reagent grade hydrochloric acid(;36%)with 900 gof deionized water.7.3 Sodium Hydroxide(NaOH)Test Solution,carefully mix200 g of reagent grade sodium hydroxide solution(;50%)with 800 g of deionized water.7.4 Oil/Solvent Test Mixture,prepare a fifty percen
16、t(50%)by weight mixture of reagent grade perchloroethylene in USPgrade mineral oil.8.Hazards8.1 Standard laboratory hygiene practices should be fol-lowed when conducting these tests.Potentially violent reac-tions may occur in performance of this test,so appropriateprecautions may be advised.8.2 All tests should be performed in a laboratory fume hood.Waste samples may produce toxic or noxious fumes whenmixed with other substances.8.3 The analyst should wear gloves that are resistant toacids,bases