1、Designation:D526613Standard Practice forEstimating the Percentage of Wood Failure in AdhesiveBonded Joints1This standard is issued under the fixed designation D5266;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last rev
2、ision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice provides procedures for estimating thepercentage of wood failure that occurs in plywood-shear,block-shear,finger join
3、t test specimens,or any other bondlineinvolving wood.1.2 The values stated in SI units are to be regarded as thestandard.The values in parentheses are provided for informa-tion only.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is therespon
4、sibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D905 Test Method for Strength Properties of AdhesiveBonds in Shear by Compression LoadingD906
5、Test Method for Strength Properties of Adhesives inPlywood Type Construction in Shear by Tension LoadingD2559 Specification for Adhesives for Bonded StructuralWood Products for Use Under Exterior Exposure Condi-tionsD4688 Test Method for Evaluating Structural Adhesives forFinger Jointing LumberD5572
6、 Specification for Adhesives Used for Finger Joints inNonstructural Lumber ProductsD5751 Specification forAdhesives Used for Laminate Jointsin Nonstructural Lumber Products2.2 American National Standards:ANSI/HPVA HP-1-2009 American National Standard forHardwood and Decorative Plywood3ANSI A190.1-20
7、12 American National Standard for WoodProductsStructural Glued,Laminated Timber32.3 Other Documents:American Plywood Association Proposed Standard Methodfor Estimating Percentage Wood Failure on PlywoodShear Specimens4PS 1 U.S.Product Standard for Construction and IndustrialPlywood4CSA O112.9 Evalua
8、tion of Adhesives for Structural WoodProducts(Exterior Exposure)4General Technical Report FPL-GTR-1905Inspection Bureau Memorandum No.1 Interpretation ofWood Failure42.4 ASTM Adjunct:Photographs for Visually Estimating the Percentage of WoodFailure in Standard Adhesively Bonded Specimens63.Terminolo
9、gy3.1 Definitions:3.1.1 deep wood failure,nfailure that is invariably severalto many cells away from the adhesive layer,in which thefracture path is strongly influenced by the grain angle andgrowthring structure.3.1.2 shallow wood failure,nfailure that is invariablywithin the first one or two layers
10、 of cells beyond the adhesivelayer in which the fracture path is not influenced by thewoodgrain angle or growth-ring structure(see 7.7 and 8.1).1This practice is under the jurisdiction of ASTM Committee D14 on Adhesivesand is the direct responsibility of Subcommittee D14.30 on Wood Adhesives.Current
11、 edition approved May 1,2013.Published July 2013.Originally approvedin 1992.Last previous edition approved in 2005 as D5266 99(2005).DOI:10.1520/D5266-13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStand
12、ards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Hardwood Plywood&Veneer Association,1825 MichaelFaraday Drive,P.O.Box 2789,Reston,VA 20190,www.hpva.org.4Available from APA The Engineered Wood Association,7011 South 19th St.,Tacoma,WA 98466,www.
13、apawood.org.5Wood Handbook:Wood as an Engineering Material,Madison,WI:U.S.Department ofAgriculture,Forest Service,Forest Products Laboratory,508 p.2010.6Available from ASTM International Headquarters.Request Adjunct No.ADJD5266.Original adjunct produced in 1991.Copyright ASTM International,100 Barr
14、Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.1.3 wood failure,nthe rupturing of wood fibers instrength tests on bonded specimens,usually expressed as thepercentage of the total area involved which shows such failure.4.Significance and Use4.1 An estimate of wood failure i
15、s one of the principalmeans for determining the quality of an adhesively bondedwood joint.4.2 When evaluated after a water soaking,water soakingand drying,or boiling and drying,the percentage of estimatedwood failure is an important criterion for qualifying adhesivesfor use in plywood,laminated stru
16、ctural timber,adhesivelybonded wood products and for daily quality control of theprocesses for manufacturing various adhesively bonded woodproducts including but not limited to plywood and laminatedtimbers.Standards that use the percentage of wood failure areincluded in Section 2.4.3 In plywood manufactured from North American soft-wood species,the percentage of wood failure of Test MethodD906 specimens,tested wet after either a vacuum-pressuresoak-dry or boil-dry treatment,correlates with the p