1、Designation:D 5177 91(Reapproved 1996)Standard Guide forWaste Acceptance at Hazardous Waste Incinerators1This standard is issued under the fixed designation D 5177;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revi
2、sion.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide addresses the acceptance of wastes at haz-ardous waste incinerators.1.2 The purpose of this guide is to assist the user
3、indetermining the information and chemical and physical char-acteristics to be used when assessing the suitability of a wastefor incineration.1.3 This guide is intended to assist in meeting the require-ments of applicable permits.1.4 This standard does not purport to address all of thesafety concern
4、s,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:D 56 Test Method for Flash Point by Tag Closed
5、Tester2D 88 Test Method for Saybolt Viscosity3D 92 Test Method for Flash and Fire Points by ClevelandOpen Cup2D 93 Test Methods for Flash Point by Pensky-MartensClosed Tester2D 129 Test Method for Sulfur in Petroleum Products(Gen-eral Bomb Method)2D 240 Test Method for Heat of Combustion of LiquidHy
6、drocarbon Fuels by Bomb Calorimeter2D 482 Test Method for Ash from Petroleum Products2D 808 Test Method for Chlorine in New and Used Petro-leum Products(Bomb Method)2D 891 Test Methods for Specific Gravity of Liquid Indus-trial Chemicals4D 1292 Test Method for Odor in Water5D 1796 Test Method for Wa
7、ter and Sediment in Fuel Oils bythe Centrifuge Method(Laboratory Procedure)2D 2015 Test Method for Gross Calorific Value of Coal andCoke by the Adiabatic Bomb Calorimeter6D 2196 Test Method for Viscosity Measurements and Rheo-logical Properties of Non-Newtonian Materials by Rota-tional(Brookfield)Vi
8、scometer7D 2361 Test Method for Chlorine in Coal6D 2983 Test Method for Low-Temperature Viscosity ofAutomotive Fluid Lubricants Measured by BrookfieldViscometer8D 3177 Test Method for Total Sulfur in theAnalysis Sampleof Coal and Coke6D 3286 Test Method for Gross Calorific Value of Coal andCoke by t
9、he Isoperibol Bomb Calorimeter6D 3761 Test Method for Total Fluorine in Coal by theOxygen Bomb Combustion/Ion Selective ElectrodeMethod6D 3828 Test Method for Flash Point by Setaflash ClosedTester9D 4007 Test Method for Water and Sediment in Crude Oilby the Centrifuge Method(Laboratory Procedure)9D
10、4208 Test Method for Total Chlorine in Coal by theOxygen Bomb Combustion/Ion Selective ElectrodeMethod6E 203 Test Method for Water Using Karl Fischer Reagent4E 260 Practice for Packed Column Gas Chromatography10E 663 Practice for Flame Atomic Absorption Analysis11E 775 Test Methods for Total Sulfur
11、in the Analysis Sampleof Refuse-Derived Fuel12E 776 Test Method for Forms of Chlorine in Refuse-Derived Fuel12E 819 Test Method for Trace Amounts of Arsenic in Or-ganic Industrial Chemicals4E 885 Test Method for Analysis of Metals in Refuse-Derived Fuel(RDF)by Atomic Absorption Spectropho-tometry12E
12、 926 Test Method for Preparing Refuse-Derived Fuel(RDF)Samples for Analyses of Metals12F 873 Guide for Incinerating Oil Spill Wastes at TemporaryField Locations121This guide is under the jurisdiction of ASTM Committee D34 on WasteManagement and is the direct responsibility of Subcommittee D34.06 on
13、Recoveryand Reuse.Current edition approved Sept.15,1991.Published November 1991.2Annual Book of ASTM Standards,Vol 05.01.3Annual Book of ASTM Standards,Vol 04.04.4Annual Book of ASTM Standards,Vol 15.05.5Annual Book of ASTM Standards,Vol 11.01.6Annual Book of ASTM Standards,Vol 05.05.7Annual Book of
14、 ASTM Standards,Vol 06.01.8Annual Book of ASTM Standards,Vol 05.02.9Annual Book of ASTM Standards,Vol 05.03.10Annual Book of ASTM Standards,Vol 14.01.11Annual Book of ASTM Standards,Vol 03.06.12Annual Book of ASTM Standards,Vol 11.04.1Copyright ASTM,100 Barr Harbor Drive,West Conshohocken,PA 19428-2
15、959,United States.2.2SW-846 Test Methods for Evaluating Solid Waste,Physical/Chemical Methods131010 Test Method for Pensky-Martens Closed-Cup Methodfor Determining Ignitability1020Test Method for Setaflash Closed-Cup Method forDetermining Ignitability1110 Test Method for Corrosivity Toward Steel3020
16、 Test Method for Acid Digestion of Aqueous Samplesand Extracts for Total Metals for Analysis by FurnaceAtomic Absorption Spectroscopy3040Test Method for Dissolution Procedures for Oils,Greases,or Waxes3050 Test Method for Acid Digestion of Sediments,Slud-ges,and Soils6010 Inductively Coupled Plasma Method7060Test Method for Arsenic(AA,Furnace Technique)7080 Test Method for Barium(AA,Direct Aspiration)7090 Test Method for Beryllium(AA,Direct Aspiration)7130 Test Method for Cadmium(AA,Direct Aspir