ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:122.64KB ,
资源ID:178789      下载积分:13 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/178789.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_3111_-_10.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_3111_-_10.pdf

1、Designation:D311110Standard Test Method forFlexibility Determination of Hot-Melt Adhesives by MandrelBend Test Method1This standard is issued under the fixed designation D3111;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year

2、of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the flex-ibility of a hot-melt adhesive in sheet form under specific testco

3、nditions.This is a working test.Its results are useful forcomparing adhesives,not for absolute characterization ofadhesives.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of

4、 thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D907 Terminology of Adhesive

5、sE171 Practice for Conditioning and Testing Flexible BarrierPackaging3.Terminology3.1 DefinitionsMany of the terms found in this testmethod are defined in Terminology D907.3.2 Definitions of Terms Specific to This Standard:3.2.1 flexibility,nthat property of a material by virtue ofwhich it may be fl

6、exed or bowed repeatedly without undergo-ing rupture.4.Summary of Test Method4.1 Test strips of a hot-melt adhesive properly sized andconditioned,are bent 180 over a mandrel(rod).Using a freshspecimen for each test,the test is repeated with smallerdiameter mandrels until the adhesive fails on bendin

7、g.Theflexibility of the adhesive is the smallest diameter mandrel overwhich four out of five test specimens do not break.5.Significance and Use5.1 The“Mandrel Bend”test is simple and fast.It requireslittle investment in equipment and little operator training.Theprime purpose is to determine whether

8、a hot-melt adhesivemeets flexibility requirements.This test is also useful forcomparing flexibility of several adhesives.It can be used todesign adhesives by comparing the flexibility of variousformulations to meet specific end use parameters.The adhesiveflexibility can be determined at temperatures

9、 other than ambi-ent by conditioning the test apparatus and test specimens at thedesired temperature and performing the test under thesetemperature conditions.6.Apparatus6.1 The test apparatus consists of a series of differentdiameter cylindrical rods or mandrels supported at each end.There shall be

10、 enough space to permit placement of the flat sideof a test specimen tangentially at right angles to the longitu-dinal axis of the test mandrel.Individual requirements deter-mine the diameter and lengths of the rods needed.For mosttests,3.2 mm(;18in.),6.4 mm(;14in.),and 12.8 mm(;12in.)diameter by 75

11、 to 150-mm(;3 to 6-in.)long rods made ofbrass or stainless steel are satisfactory.Fig.1 describes twosimple test frames,one with fixed mandrels and the otherdesigned to take any diameter mandrel.7.Test Specimen7.1 The test specimen dimensions can be varied dependingon the end use requirements of the

12、 hot-melt adhesive.Fig.2describes a recommended specimen size.It is 10 mm(;0.4in.)wide,75 mm(;3 in.)long and 1.25 6 0.01 mm(;0.05in.)thick.The thickness dimension is critical and must beaccurately measured.The test specimens shall be cut frommolded or extruded sheets or film.Plying of several thinne

13、rsamples shall not be permitted.No flaws visible anywhere inthe sample to the naked eye shall be permitted.1This test method is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.14 on Tape andLabels.Current edition approved Oct.1,2010.Publi

14、shed October 2010.Originallyapproved in 1972.Last previous edition approved in 2004 as D3111 99(2004)1.DOI:10.1520/D3111-10.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer

15、to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 8.Conditioning8.1 Store the test specimens and test apparatus at the testconditions for 24 h.Perform the test under these samecondit

16、ions.Forrapidscreening,particularlyatlowtemperatures,a minimum of 4 h conditioning can be used.Notethis change when recording data.If other conditions are notspecified,the storage and test conditions will be 23 6 2C andNOTE1(Recess to fit test frame)Figures in parentheses are approximate.FIG.1 Test Mandrel(Various Diameters)for Test FrameFIG.2 Test SpecimenD3111 102 50 6 5%relative humidity.Specification E171,details theseand other tests conditions.9.Failure9.1 Failure is a visible fracture,craz

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2