1、Designation:D303415Standard Specification forType PSM Poly(Vinyl Chloride)(PVC)Sewer Pipe andFittings1This standard is issued under the fixed designation D3034;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision
2、.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers requirements and test me
3、thodsfor materials,dimensions,workmanship,flattening resistance,impact resistance,pipe stiffness,extrusion quality,joiningsystems and a form of marking for type PSM poly(vinylchloride)(PVC)sewer pipe and fittings.1.2 Pipe and fittings produced to this specification should beinstalled in accordance w
4、ith Practice D2321.1.3 The text of this specification references notes,footnotes,and appendixes which provide explanatory material.Thesenotes and footnotes(excluding those in tables and figures)shallnot be considered as requirements of the specification.1.4 The values stated in inch-pound units are
5、to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 The following precautionary caveat pertains only to thetest methods portion,Section 8,of this specification:Thisstandard does no
6、t purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2D6
7、18 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride)(PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC)CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and Fit
8、tingsD2152 Test Method for Adequacy of Fusion of ExtrudedPoly(Vinyl Chloride)(PVC)Pipe and Molded Fittings byAcetone ImmersionD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharac
9、teristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D2564 Specification for Solvent Cements for Poly(VinylChloride)(PVC)Plastic Piping SystemsD2749 Symbols for Dimensions o
10、f Plastic Pipe FittingsD2855 Practice for Making Solvent-Cemented Joints withPoly(Vinyl Chloride)(PVC)Pipe and FittingsD3212 Specification for Joints for Drain and Sewer PlasticPipes Using Flexible Elastomeric SealsF412 Terminology Relating to Plastic Piping SystemsF1336 Specification for Poly(Vinyl
11、 Chloride)(PVC)Gas-keted Sewer Fittings2.2 Federal Standard:3Fed.Std.No.123 Marking for Shipment(Civil Agencies)2.3 Military Standard:3MIL-STD-129 Marking for Shipment and Storage3.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412,and abbreviations are in accordance with
12、 Termi-nology D1600,unless otherwise specified.The abbreviation ofpoly(vinyl chloride)plastics is PVC.3.1.1 The term PSM is not an abbreviation but rather anarbitrary designation for a product having certain dimensions.1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPip
13、ing Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.Current edition approved Nov.1,2015.Published December 2015.Originallyapproved in 1972.Last previous edition approved in 2014 as D3034 14a.DOI:10.1520/D3034-15.2For referenced ASTM standards,visit the ASTM website,www.astm.
14、org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from DLA Document Services Building 4/D 700 Robbins AvenuePhiladelphia,PA 19111-5094 http:/quicksearch.dla.mil/*A Summ
15、ary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.Significance and Use4.1 The requirements of this specification are intended toprovide pipe and fittings suitable for non-pressure
16、drainage ofsewage and surface water.NOTE1Industrial waste disposal lines should be installed only withthe specific approval of the cognizant code authority since chemicals notcommonly found in drains and sewers and temperatures in excess of 60C(140F)may be encountered.5.Basic Materials5.1 Pipe shall be made of PVC plastic having a cellclassification of 12454 or 12364 as defined in SpecificationD1784.5.2 Fittings shall be made of PVC plastic having a cellclassification of 12454 or 13343 as define