1、Designation:D345015(Reapproved 2020)Standard Test Method forWashability Properties of Interior Architectural Coatings1This standard is issued under the fixed designation D3450;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year
2、of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method covers the determi
3、nation of the relativeease of removing soilant discolorations from the dried film ofan interior coating by washing with either an abrasive ornonabrasive cleaner.1.2 This test method is limited to coatings having a CIE-Yreflectance of 60%or more,as measured in accordance withTest Method E1347.1.3 The
4、 values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate s
5、afety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of
6、 International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D562 Test Method for Consistency of Paints MeasuringKrebs Unit(KU)Viscosity Using a Stormer-Type Viscom-eterD1193 Specificati
7、on for Reagent WaterD1210 Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type GageE70 Test Method for pH of Aqueous Solutions With theGlass ElectrodeE1347 Test Method for Color and Color-Difference Mea-surement by Tristimulus Colorimetry3.Terminology3.1 Definitions of Te
8、rms Specific to This Standard:3.1.1 soilant,na discoloring substance that clings to thesurface of a coating,whose dispersed color component is not insolution and therefore does not penetrate into the film.3.1.1.1 DiscussionSoilant differs from stain in that thecolorant of a stain is in solution and,
9、therefore,can penetrateinto the film.4.Summary of Test Method4.1 The test material is applied to a black plastic panel andallowed to dry for 7 days.The reflectance of the film ismeasured(R1)and then a soilant consisting of carbon blackdispersed in mineral oil is applied on the film.The panel isplace
10、d on a glass plate in a washability machine and the film iswashed with either an abrasive or nonabrasive scrub mediumfor 100 cycles.The panel is rinsed and dried and the reflectancein the stained area is read(R2).The ratio of the reflectance,R2/R1,is a measure of the degree to which the soilant has
11、beenremoved.5.Significance and Use5.1 Interior architectural paints are often discolored by dirtand other soilant materials.This test method covers the relativeease and completeness of removal of a specific soilant fromsuch a surface by scrubbing.The greater the ease of soilremoval with a minimum of
12、 film erosion,the greater the usefulservice life is expected to be.5.2 Results obtained by this test method do not necessarilycorrelate with all types of soilants.5.3 Semigloss finishes generally require only the nonabra-sive type cleaner for good soilant removal,whereas flat paintsmay require the a
13、brasive type.1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.42 on Architectural Coatings.Current edition approved Dec.1,2020.Published December 2020.Originallyapproved in 19
14、75.Last previous edition approved in 2015 as D3450 15.DOI:10.1520/D3450-15R20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe A
15、STM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment o
16、f International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.16.Apparatus6.1 Washability Tester,3also referred to as a straight linewashability machine.6.1.1 Accessory Apparatus:6.1.1.1 Glass Plate,measured to fit,454 by 165 by 6.3 mm(1778by 612by14in.),6.1.1.2 Stainless Steel Pan,6.1.1.3“C”Clamps,6.1.1.4 Scale,standard,6.1.1.5 White Blotter,and6.1.1.6 Holder,brass,measuring 95 by 76 by 25.4 mm(334by 3 by 1 in.).6.2 U-Shape