ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:88.71KB ,
资源ID:179446      下载积分:14 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/179446.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_3776_-_D_3776M_-_09a_2013.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_3776_-_D_3776M_-_09a_2013.pdf

1、Designation:D3776/D3776M09a(Reapproved 2013)Standard Test Methods forMass Per Unit Area(Weight)of Fabric1This standard is issued under the fixed designation D3776/D3776M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of las

2、t revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope1.1 These test methods cover the measurement of f

3、abricmass per unit area(weight)and is applicable to most fabrics.1.2 There are four approved options:1.2.1 Option AFull Piece,Roll,Bolt or Cut(Section 7).1.2.2 Option BFull Width Sample(Section 8).1.2.3 Option CSmall Swatch of Fabric(Section 9).1.2.4 Option DNarrow Fabrics(Section 10).1.3 The values

4、 stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.4 T

5、his standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2

6、.1 ASTM Standards:2D123 Terminology Relating to TextilesD1776 Practice for Conditioning and Testing TextilesD3773 Test Methods for Length of Woven FabricD3774 Test Method for Width of Textile Fabric2.2 Other Standard:ANSI/ASQC Z1.4 Inspection by Attributes33.Terminology3.1 The following terms are re

7、levant to this standard:weight.3.2 For definitions of all other textile terms see TerminologyD123.4.Summary of Test Methods4.1 Fabric mass is calculated from the mass of a specimenthe length and width of which have been measured as directedin one of the procedures in Test Method D3773 and D3774.5.Ap

8、paratus5.1 Scale,with a capacity and sensitivity sufficient to weighthe full piece,roll,bolt,or cut units to within 60.1%of theirgross mass.The accuracy of the scale should be certified by arecognized authority.5.2 Balance,having a capacity and sensitivity to weighwithin 60.1%of the mass of the spec

9、imens being tested.5.3 Cutting Die,either square or round with an area of atleast 13 cm2or 2 in.26.Conditioning6.1 Condition test specimens as directed in Practice D1776.6.2 All weighing tests should be made in the standardatmospherefortestingtextiles(21 6 1C(70 6 2F),65 6 2%RH),after the specimens

10、have been conditioned inthe same atmosphere.It may be impractical to condition thespecimens in Option A or nonconditioned testing may beagreed upon by the purchaser and supplier.When the full rollsor bolts of fabric cannot be properly conditioned in a reason-able time with available facilities,perfo

11、rm the tests withoutconditioning and report the actual conditions prevailing at thetime of the test.Such results may not correspond with theresults obtained after testing adequately conditioned specimensin the standard atmosphere for testing textiles.7.Option AFull Piece,Roll,Bolt,or Cut7.1 Signific

12、ance and Use7.1.1 OptionAfor the determination of mass per unit area ofwoven fabrics may be used for acceptance testing of commer-cial shipments since it has been used extensively in the trade.1These test methods are under the jurisdiction of ASTM Committee D13 onTextiles and are the direct responsi

13、bility of Subcommittee D13.60 on Fabric TestMethods,Specific.Current edition approved July 1,2013.Published September 2013.ReplacesSections 35 to 41 of Methods D1910 64(1975).Originally approved in 1979.Lastprevious edition approved in 2009 as D3776 09a2.DOI:10.1520/D3776_D3776M-09AR13.2For referenc

14、ed ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th F

15、loor,New York,NY 10036,http:/www.ansi.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 7.1.2 In case of a dispute arising from differences inreported test values when using Test Methods D3776 foracceptance testing of commercial shipmen

16、ts,the purchaser andthe supplier should conduct comparative tests to determine ifthere is a statistical bias between their laboratories.Competentstatistical assistance is recommended for the investigation ofbias.As a minimum,the two parties should take a group of testspecimens which are as homogeneous as possible and whichare from a lot of material of the type in question.The testspecimens should then be randomly assigned in equal numbersto each laboratory for testing.The average results from th

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2