1、Designation:D299617An American National StandardStandard Specification forFilament-Wound“Fiberglass”(Glass-Fiber-ReinforcedThermosetting-Resin)Pipe1This standard is issued under the fixed designation D2996;the number immediately following the designation indicates the year oforiginal adoption or,in
2、the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers machine-made reinforced ther-mosetting resin pressure pipe(RTRP
3、)manufactured by thefilament winding process up to 60 in.nominal size.Includedare a classification system and requirements for materials,mechanical properties,dimensions,performance,methods oftest,and marking.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in
4、 parentheses are provided forinformation purposes only.1.3 The following safety hazards caveat pertains only to thetest method portion,Section 8,of this specification:Thisstandard does not purport to address all of the safety problems,if any,associated with its use.It is the responsibility of the us
5、erof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.NOTE1The term“fiberglass pipe”as described in Section 3 of thisspecification applies to both reinforced thermosetting resin pipe(RTRP)and reinforced polymer
6、mortar pipe(RPMP).This specification coversonly reinforced thermosetting resin pipe(RTRP).NOTE2This specification is applicable to RTRP where the ratio ofoutside diameter to wall thickness is 10:1 or more.NOTE3There is no known ISO equivalent to this standard.NOTE4For the purposes of this standard,p
7、olymer does not includenatural polymers.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World
8、Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD883 Terminology Relating to PlasticsD1598 Test Method for Time-to-Failure of Plastic PipeUnder
9、Constant Internal PressureD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe,Tubing,and FittingsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2105 Test Method for Longitudinal Tensile Properties of“Fiberglass”(Glass-Fiber-Reinforced Thermosetting-Resin)Pi
10、pe and TubeD2143 Test Method for Cyclic Pressure Strength ofReinforced,Thermosetting Plastic PipeD2310 Classification for Machine-Made“Fiberglass”(Glass-Fiber-Reinforced Thermosetting-Resin)Pipe(Withdrawn 2017)3D2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by
11、 Parallel-Plate LoadingD2992 Practice for Obtaining Hydrostatic or Pressure De-sign Basis for“Fiberglass”(Glass-Fiber-ReinforcedThermosetting-Resin)Pipe and FittingsD3567 Practice for Determining Dimensions of“Fiberglass”(Glass-Fiber-Reinforced Thermosetting Resin)Pipe andFittingsF412 Terminology Re
12、lating to Plastic Piping Systems3.Terminology3.1 Definitions:3.1.1 GeneralDefinitions are in accordance with Termi-nologies D883 and F412 and abbreviations are in accordance1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee
13、 D20.23 on ReinforcedPlastic Piping Systems and Chemical Equipment.Current edition approved Aug.1,2017.Published August 2017.Originallyapproved in 1971.Last previous edition approved in 2015 as D2996 15.DOI:10.1520/D2996-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact
14、 ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this s
15、tandardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of Int
16、ernational Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 with Terminology D1600,unless otherwise indicated.Theabbreviation for reinforced thermosetting resin pipe is RTRP.3.2 Definitions of Terms Specific to This Standard:3.2.1 coatinga resin layer,with or without filler orreinforcement,or both,applied to the exterior surface of thepipe structural wall.3.2.2 fiberglass pipea tubular product containing glass-fiber reinforce