ImageVerifierCode 换一换
格式:PDF , 页数:7 ,大小:112.88KB ,
资源ID:179633      下载积分:14 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/179633.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_3295_-_15.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_3295_-_15.pdf

1、Designation:D329515Standard Specification forPTFE Tubing,Miniature Beading and Spiral Cut Tubing1This standard is issued under the fixed designation D3295;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A nu

2、mber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers PTFE tubing,miniature bead-in

3、g and spiral cut tubing-manufactured from PTFE resinproduced from dispersion specified in Specification D4895.NOTE1PTFE tube and rod manufactured from resin specified inSpecification D4894 are covered in Specification D1710.1.2 The values stated in SI units are to be regarded asstandard.The inch-pou

4、nd units given in parentheses are forinformation only.1.3 The following hazard caveat pertains only to the testmethod portion,Section 8,of this specification:This standarddoes not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the user of thi

5、sstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.1.4 As PTFE resin produced from dispersion is not a truethermoplastic material,any reuse for the specification refer-enced above is impossible.However,markets do exist

6、fornon-virgin PTFE as additives and fillers.NOTE2There is no known ISO equivalent to this standard.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD792 Test Methods for Density and Specific Gravity(Rela-t

7、ive Density)of Plastics by DisplacementD883 Terminology Relating to PlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1675 Test Methods for Polytetrafluoroethylene TubingD1708 Test Method for Tensile Properties of Plastics by Useof Microtensile SpecimensD1710 Specification for Ext

8、ruded Polytetrafluoroethylene(PTFE)Rod,Heavy Walled Tubing and Basic ShapesD3892 Practice for Packaging/Packing of PlasticsD4894 Specification for Polytetrafluoroethylene(PTFE)Granular Molding and Ram Extrusion MaterialsD4895 Specification for Polytetrafluoroethylene(PTFE)Resin Produced From Dispers

9、ion3.Terminology3.1 DefinitionsThe terminology given in TerminologiesD883 and D1600 is applicable to this specification.3.2 Description of Term Specific to This Standard:3.2.1 lota single production run,or a uniform blend of twoor more production runs.4.Classification4.1 This specification provides

10、for five groups of PTFEtubing,miniature beading and spiral cut tubing,differentiatedby size and type.The groups are further subdivided into classesbased on wall thickness.4.1.1 Group 01Tubing based upon the American WireGage(AWG)sizes.4.1.2 Group 02Tubing based upon fractional inch sizes.4.1.3 Group

11、 03Tubing specified by inner diameter andwall thickness in Table 6 referred to as“Custom or Metric.”4.1.4 Group 04Tubing cut to form spiral wrap as in Table7.4.1.5 Group 05Miniature beading having diameters aslisted in Table 8.4.2 The types are further differentiated in accordance withincreasing wal

12、l thickness as follows:4.2.1 Class 1Tubing having walls tabulated in Table 1listed as light wall.4.2.2 Class 2Tubing having walls of greater thicknessthan Class 1 listed as thin wall.4.2.3 Class 3Tubing having walls tabulated in Table 2listed as standard wall.4.2.4 Class 4Tubing having walls tabulat

13、ed in Table 3listed as chemical tubing.1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.15 on ThermoplasticMaterials(Section D20.15.12).Current edition approved Sept.1,2015.Published September 2015.Originallyapproved

14、in 1974.Last previous edition approved in 2011 as D3295-06(2011).DOI:10.1520/D3295-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page

15、 onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.2.5 Class 5Tubing having walls tabulated in Table 2 andTable 3 listed as heavy wall.4.3 A one-line syst

16、em may be used to specify materialscovered by this specification.The system uses predefined cellsto refer to specific aspects of this specification,as illustratedbelow.SpecificationStandard Number:BlockGroup:Class:Grade:Special NotesExample:SpecificationD3295 0101124For this example,the line callout would be SpecificationD3295 01,01124 and would specify tubing having wallsTABLE 1 Dimensions and Tolerances for Group 01 PTFE Tubing,mm(in.)(Classes 1 and 2)AWG SizeGradeInside DiameterClass 1Light W

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2