1、Designation:D3531/D3531M16Standard Test Method forResin Flow of Carbon Fiber-Epoxy Prepreg1This standard is issued under the fixed designation D3531/D3531M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revision.A n
2、umber in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method covers the determination of the amount
3、of resin flow that will take place from prepreg tape or sheetunder given conditions of temperature and pressure.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shal
4、l be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.2.1 Within the text,inch-pound units are shown in brack-ets.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is therespo
5、nsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to PlasticsD3878 Terminology for Composite Materials3.Terminology3.
6、1 DefinitionsTerminology D3878 defines terms relatingto high-modulus fibers and their composites.TerminologyD883 defines terms relating to plastics.In the event of aconflict between terms,Terminology D3878 shall have prece-dence over other standards.3.2 Symbols:3.2.1 RFresin flow3.2.2 W1weight of th
7、e prepreg specimen prior to flow test3.2.3 W2weight of the specimen assembly prior to heating3.2.4 W3weight of the specimen assembly after heating3.2.5 W4weight of the prepreg specimen after flow test4.Summary of Test Method4.1 A weighed specimen consisting of two plies a minimumsize of 50-mm 2.0-in
8、.square,oriented in a 0/90 crossplyconfiguration,and sandwiched between bleeder material andrelease film.The sandwich is placed in a platen press heated toeither temperature A,120C 250F,or temperature B,175C350F or another specified temperature.The press is closed toprovide a pressure of 700 kPa 100
9、 psi.The pressure is heldfor 15 min or until the resin gels.The cooled sandwichassembly is removed and the resin that has flowed to the edgesof the specimen is removed and the specimen reweighed.Thechange in weight is expressed as a percent of the originalweight and reported as percent flow.5.Signif
10、icance and Use5.1 This test method is used to obtain the resin flow ofcarbon fiber-epoxy prepreg tape or sheet material.It is suitablefor comparing lots of material of supposedly the same charac-teristics and also for comparative evaluation of materialsproduced by different vendors using different r
11、esin-fiber com-binations.5.2 Composite parts are laminated from prepreg material atvarious pressures and temperatures.Production process designwill require a flow test be run at a temperature and a pressureclose to that of the actual molding conditions.All methods ofmeasuring resin flow are dependen
12、t on the size and geometryof the specimen.This test method uses the smallest quantity oftape that will give reproducible results.5.2.1 The percent resin flow of a single fiber and resinsystem at a temperature and pressure varies with the volatilecontent,degree of advancement of epoxy resin,and with
13、theresin content of the prepreg tape or sheet.5.2.2 As volatile content and degree of resin cure(advance-ment)change with time,this test method is useful in comparingthe life of prepreg tape and sheet.1This test method is under the jurisdiction of ASTM Committee D30 onComposite Materials and is the
14、direct responsibility of Subcommittee D30.03 onConstituent/Precursor Properties.Current edition approved Nov.1,2016.Published November 2016.Originallyapproved in 1976.Last previous edition approved in 2011 as D3531 11.DOI:10.1520/D3531_D3531M-16.2For referenced ASTM standards,visit the ASTM website,
15、www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.Interfer
16、ences6.1 This test method depends on platen force being suppliedevenly to the specimen.For this to be done,the platen mustload evenly across its surface and not point load to the point ofinitial contact.When bleeder materials are used on the top andbottom of the specimen,the effect of uneven pressure applica-tion is less pronounced than if no bleeder materials are used.Bleeders tend to minimize pressure effects,since if resin flowsinto the bleeder it will do so within a broad pressure range.Some