1、Designation:D372322Standard Test Method forPigment Content of Water-Emulsion Paints by Low-Temperature Ashing1This standard is issued under the fixed designation D3723;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last
2、revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers a procedure for the pigmentcontent determination of water-based paints.It is applicableonly to pigments
3、that do not decompose or lose weight attemperatures below 500 C.Such pigments include most metaloxides,silicates,and a majority of anhydrous inorganic salts.1.2 Many water-based paints contain pigments and organiccolorants that lose water of hydration or decompose at thistemperature.The residual ash
4、 should be carefully inspected forchanges in color or texture that could indicate a pigmentalteration and hence lead to erroneous results.Caution shouldtherefore be exercised when applying this test method tosamples containing unknown pigment compositions.1.3 The values stated in SI units are to be
5、regarded asstandard.No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practic
6、es and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Re
7、com-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent Water3.Significance and Use3.1 This test method is used by paint producers and con-sumers for product process control and for produ
8、ct acceptance.4.Apparatus4.1 Oven,forced draft,maintained at 105 6 2 C.4.2 Furnace,muffle,maintained at 450 6 25 C.4.3 Syringe,5-mL.4.4 Aluminum Foil Dish,58 mm in diameter by 18 mm highwith a flat bottom.The bottom of the dish should be as nearlyflat as possible so that a uniform film is produced.5
9、.Reagents5.1 Purity of ReagentsReagent grade chemicals shall beused in all tests.Unless otherwise indicated,it is intended thatall reagents shall conform to the specifications of the Commit-tee on Analytical Reagents of the American Chemical Society,where such specifications are available.3Other gra
10、des may beused,provided it is first ascertained that the reagent is ofsufficiently high purity to permit its use without lessening theaccuracy of the determination.5.2 Purity of WaterUnless otherwise indicated,referencesto water shall be understood to mean reagent water conformingto Type III of Spec
11、ification D1193.5.3 Ammonium Hydroxide4Add 1 volume of concen-trated NH4OH(sp gr 0.90)to 3 volumes of water.6.Procedure6.1 Mix samples until homogeneous,preferably on a me-chanical shaker.If air bubbles become entrapped in a sample,stir it by hand.1This test method is under the jurisdiction of ASTM
12、Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.21 on Chemical Analysis of Paints and Paint Materials.Current edition approved July 1,2022.Published July 2022.Originally approvedin 1978.Last previous edition approved in 2017 a
13、s D3723 05(2017).DOI:10.1520/D3723-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3ACS Reagent Chemicals,Speci
14、fications and Procedures for Reagents andStandard-Grade Reference Materials,American Chemical Society,Washington,DC.For suggestions on the testing of reagents not listed by the American ChemicalSociety,see Analar Standards for Laboratory Chemicals,BDH Ltd.,Poole,Dorset,U.K.,and the United States Pha
15、rmacopeia and National Formulary,U.S.Pharma-copeial Convention,Inc.(USPC),Rockville,MD.4For guidance in the safe handling of ammonium hydroxide consult theManufacturing Chemists Associations Chemical Safety Data Sheet.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,P
16、A 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.16.2 Draw approximately 1.5 g of the test paint into a 5-mLsyringe and weigh to 1 mg.Add the paint dropwise(about 30drops)into a preweighed,tared aluminum dish