1、Designation:D416506(Reapproved 2020)1Standard Test Method forCyanogen Chloride in Water1This standard is issued under the fixed designation D4165;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in p
2、arentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEWarning notes were editorially updated throughout in January 2020.1.Scope1.1 This test method covers the determination of cyanogenchloride in water.Cyanogen
3、 chloride is normally present onlyat very low concentrations;it is a very labile and sparselysoluble gaseous compound.Water samples may contain cya-nogen chloride after the chlorination of waste waters contain-ing cyanide or thiocyanate compounds.1.2 Cyanogen chloride is unstable.A quick test using
4、a spotplate or comparator as soon as the sample is collected may bethe best test,reducing the loss of cyanogen chloride during thetime lapse between sampling and analysis.(See Fig.1 for atypical decay curve for cyanogen chloride in a solution.)1.3 This test method has been used successfully withreag
5、ent water.The analyst is responsible for determiningwhether the test method is applicable to the water matrix beingtested.Reference is made to Test Method D of Test MethodsD2036 which is based on similar chemical reactions and hasbeen evaluated by collaborative testing in this matrix.1.4 The lower l
6、imit of detectability is 0.005 mg CN/L.1.5 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user
7、 of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.Specific hazard statements are given in 8.5 and 8.7 and Section9.1.7 This international standard was developed in accor-dance with internation
8、ally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1129 Terminolo
9、gy Relating to WaterD1193 Specification for Reagent WaterD2036 Test Methods for Cyanides in WaterD3370 Practices for Sampling Water from Flowing ProcessStreamsD3856 Guide for Management Systems in LaboratoriesEngaged in Analysis of WaterD4210 Practice for Intralaboratory Quality Control Proce-dures
10、and a Discussion on Reporting Low-Level Data(Withdrawn 2002)3D5789 Practice for Writing Quality Control Specificationsfor Standard Test Methods for Organic Constituents(Withdrawn 2002)3D5847 Practice for Writing Quality Control Specificationsfor Standard Test Methods for Water AnalysisE60 Practice f
11、or Analysis of Metals,Ores,and RelatedMaterials by SpectrophotometryE275 Practice for Describing and Measuring Performance ofUltraviolet and Visible Spectrophotometers3.Terminology3.1 Definitions:3.1.1 For definitions of terms used in this standard,refer toTerminology D1129.4.Summary of Test Method4
12、.1 The water sample is mixed with a pyridine-barbituricacid solution and the color produced is measured with aspectrophotometer.1This test method is under the jurisdiction of ASTM Committee D19 on Waterand is the direct responsibility of Subcommittee D19.06 on Methods forAnalysis forOrganic Substanc
13、es in Water.Current edition approved Jan.1,2020.Published January 2020.Originallyapproved in 1982.Last previous edition approved in 2012 as D4165 06(2012).DOI:10.1520/D4165-06R20E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.
14、For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.Unite
15、d StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers t
16、o Trade(TBT)Committee.5.Significance and Use5.1 The presence of cyanogen chloride in chlorinated sani-tary and industrial effluents and therefore receiving waters is ofconcern because of its toxicity to aquatic life.5.2 This test method provides an analytical procedure formeasuring cyanogen chloride in water.5.3 This test method is applicable for clean metal finishingand chlorinated sanitary and industrial effluents,and also canbe used to establish process control of cyanide destruction bychlori