1、Designation:D342719Designation 31301Standard Test Method forAir Release Properties of Hydrocarbon Based Oils1This standard is issued under the fixed designation D3427;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last r
2、evision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the ability of turbine,hydraulic,and gear oils to separate entrained air.NOTE1This test method was devel
3、oped for hydrocarbon based oils.It may be used for some synthetic fluids;however,the precision statementapplies only to hydrocarbon based oils.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport
4、 to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was de
5、veloped in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Docum
6、ents2.1 ASTM Standards:2D1193 Specification for Reagent WaterD1401 Test Method for Water Separability of Petroleum Oilsand Synthetic FluidsD4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsE1 Specification for ASTM Liquid-in-Glass Thermometers2.2 DIN Standard:3DIN 51 3813.Terminol
7、ogy3.1 Definitions of Terms Specific to This Standard:3.1.1 air release time,nthe number of minutes needed forair entrained in the oil to reduce in volume to 0.2%under theconditions of this test and at the specified temperature.4.Summary of Test Method4.1 Compressed air is blown through the test oil
8、,which hasbeen heated to a temperature of 25 C,50 C,or 75 C.Afterthe air flow is stopped,the time required for the air entrainedin the oil to reduce in volume to 0.2%is recorded as the airrelease time.NOTE2By agreement between the customer and the laboratory,the oilmay be heated at other temperature
9、s.However,the precision at thesedifferent temperatures is not known at present.5.Significance and Use5.1 Agitation of lubricating oil with air in equipment,suchas bearings,couplings,gears,pumps,and oil return lines,mayproduce a dispersion of finely divided air bubbles in the oil.Ifthe residence time
10、 in the reservoir is too short to allow the airbubbles to rise to the oil surface,a mixture of air and oil willcirculate through the lubricating oil system.This may result inan inability to maintain oil pressure(particularly with centrifu-gal pumps),incomplete oil films in bearings and gears,andpoor
11、 hydraulic system performance or failure.5.2 This test method measures the time for the entrained aircontent to fall to the relatively low value of 0.2%volumeunder a standardized set of test conditions and hence permitsthe comparison of the ability of oils to separate entrained airunder conditions w
12、here a separation time is available.Thesignificance of this test method has not been fully established.However,entrained air can cause sponginess and lack ofsensitivity of the control of turbine and hydraulic systems.This1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum P
13、roducts,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.C0.02 on Corrosion and Water/Air Separability.Current edition approved Dec.1,2019.Published January 2020.Originallyapproved in 1975.Last previous edition approved in 2015 as D3427 15.DOI:10.1520/D3427-19.This sta
14、ndard has been developed through the cooperative effort between ASTMInternational and the Energy Institute,London.The EI and ASTM Internationallogos imply that the ASTM International and EI standards are technicallyequivalent,but does not imply that both standards are editorially identical.Adoptedas
15、 a joint ASTM/IP standard in 2006.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Beuth Verlag Gmb
16、H,Burggrafenstrasse 6,1000 Berlin 30,Germany.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical