ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:57.94KB ,
资源ID:180352      下载积分:14 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/180352.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_4426_-_01_2021.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_4426_-_01_2021.pdf

1、Designation:D442601(Reapproved 2021)Standard Test Method forDetermination of Percent Nonvolatile Content of LiquidPhenolic Resins Used for Wood Laminating1This standard is issued under the fixed designation D4426;the number immediately following the designation indicates the year oforiginal adoption

2、 or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the recommended procedure forthe determination of the nonvo

3、latile or total solids content ofliquid phenolic resins used for wood laminating.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with

4、its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized princi

5、ples on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D907 Terminology of AdhesivesD1582 Te

6、st Method for Nonvolatile Content of LiquidPhenol,Resorcinol,and Melamine Adhesives3.Terminology3.1 DefinitionsMany of the terms in this test method aredefined in Terminology D907.4.Summary of Test Method4.1 A weighed specimen is oven-dried,cooled in adesiccator,and weighed.The percent nonvolatile c

7、ontent iscalculated,based on the amount remaining.5.Significance and Use5.1 This test method is intended as a fast and economicaldetermination of the nonvolatile content of liquid phenolicresins used for wood laminating and is useful for generalcomparative purposes.For greater precision and accuracy

8、,TestMethod D1582 is recommended.6.Apparatus6.1 Disposable Aluminum Foil Dishes,60-mm(2.4-in.)diameter by 16-mm(0.60-in.)depth.NOTE1A glass dish may be used if the pH of the resin is greater thanten.6.2 Desiccator,charged with Drierite or equivalent desic-cant.6.3 Mechanical Convection Oven.6.4 Anal

9、ytical Balance,accurate to 60.1 mg(0.000002 lb).6.5 Eye Droppers,or Dropping Pipettes,2-mL capacity.6.6 Anemometer.6.7 Stainless Steel Trays,fabricated 30 gauge,83 by 250mm(3.25 by 9.8 in.),with 19-mm(0.75-in.)sides and openends.6.8 Modified Oven Shelves,fitted with fabricated 18-gauge19 by 19-mm(0.

10、75 by 0.75-in.)stainless steel angle stoppositioned 108 mm(4.25 in.)from back edge.Shelf-stopensures consistent solids dish placement and prevents place-ment at the rear of the oven where airflow is erratic.6.9 Laboratory Hotplate,with heating capacity to 270C(518F).7.Oven Setup and Periodic Check S

11、pecifications7.1 Specifications:7.1.1 Intake Port6.4 mm(0.25 in.)open.7.1.2 Exhaust Port6.4 mm(0.25 in.)open.7.1.3 Internal Airflow91.4 6 1 m/min(300 6 3 ft/min)at40C(104F).7.1.4 Temperature125 6 1C(257 6 2F).7.2 A 6.4-mm(0.25-in.)metal spacer is a convenient toolfor setting port openings.1This test

12、 method is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.30 on WoodAdhesives.Current edition approved April 1,2021.Published April 2021.Originallyapproved in 1984.Last previous edition approved in 2013 as D4426 01(2013).DOI:10.1520/D442

13、6-01R21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box

14、C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the Wor

15、ld Trade Organization Technical Barriers to Trade(TBT)Committee.17.3 Measure with Davis-type anemometer placed as close aspossible to the geometric center of the cavity with the doorshut.7.4 Set the oven temperature at 125C(257F)and recordthe actual temperature for a period of 2 h.The control ranges

16、hall be 61C(2F)during the check period.8.Sampling8.1 Take a representative sample of the lot of resin beingevaluated of a sufficient quantity for the tests.While the testsconsume less than 5 g(0.01 lb)of resin,a sample of at least250 g(0.55 lb)is recommended to ensure that it is represen-tative and that rechecks can be made if desired.8.2 To ensure that surface evaporation of solvent does notaffect the accuracy of the results,mix the resin samplethoroughly just prior to the test.9.Sample Dish Pr

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2