1、Designation:D390315(Reapproved 2022)Standard Specification forRubber Seals Used in Air-Heat Transport of Solar EnergySystems1This standard is issued under the fixed designation D3903;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,th
2、e year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the general requirements forthe rubber seals used in solar energy systems employingair-
3、heat transport.Examples are duct and damper seals.Par-ticular applications may necessitate other requirements thatwould take precedence over these requirements when speci-fied.NOTE1Rubber seals for the collector are covered in SpecificationsD3667 and D3771.1.2 Design requirement pertains only to per
4、missible deflec-tions of the rubber during thermal expansion or contraction ofthe seal in use and the tolerances in dimensions of molded andextruded seals.1.3 This specification does not include requirements per-taining to the fabrication or installation of the seals.1.4 The values stated in SI unit
5、s are to be regarded asstandard.No other units of measurement are included in thisstandard.1.5 The following safety hazards caveat pertains only to thetest methods portion,Section 10,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its
6、use.It is the responsibility of the userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on
7、standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C661 Test Method for Indentation Hardness of
8、Elastomeric-Type Sealants by Means of a DurometerC717 Terminology of Building Seals and SealantsC719 Test Method for Adhesion and Cohesion of Elasto-meric Joint Sealants Under Cyclic Movement(HockmanCycle)D395 Test Methods for Rubber PropertyCompression SetD412 Test Methods for Vulcanized Rubber and
9、 Thermoplas-tic ElastomersTensionD865 Test Method for RubberDeterioration by Heating inAir(Test Tube Enclosure)D1149 Test Methods for Rubber DeteriorationCracking inan Ozone Controlled EnvironmentD1229 Test Method for Rubber PropertyCompression Setat Low TemperaturesD1349 Practice for RubberStandard
10、 Conditions for Test-ingD1415 Test Method for Rubber PropertyInternationalHardnessD1566 Terminology Relating to RubberD2137 Test Methods for Rubber PropertyBrittleness Pointof Flexible Polymers and Coated FabricsD2240 Test Method for Rubber PropertyDurometer Hard-nessD3182 Practice for RubberMateria
11、ls,Equipment,and Pro-cedures for Mixing Standard Compounds and PreparingStandard Vulcanized SheetsD3183 Practice for RubberPreparation of Pieces for TestPurposes from ProductsD3667 Specification for Rubber Seals Used in Flat-PlateSolar CollectorsD3771 Specification for Rubber Seals Used in Concentra
12、tingSolar Collectors1This specification is under the jurisdiction ofASTM Committee D11 on Rubberand Rubber-like Materials and is the direct responsibility of Subcommittee D11.37on Coated Fabrics,Rubber Threads and Seals.Current edition approved Oct.1,2022.Published November 2022.Originallyapproved i
13、n 1980.Last previous edition approved in 2015 as D3903 15.DOI:10.1520/D3903-15R22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page ont
14、he ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopme
15、nt of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1G7 Practice for Natural Weathering of MaterialsG151 Practice for Exposing Nonmetallic Materials inAccel-erated Test Devices that Use Laboratory Light SourcesG155
16、 Practice for Operating XenonArc LampApparatus forExposure of Materials2.2 Other Standards:RMA HandbookRubber Products:Molded,Extruded,Lathe Cut,and Cellular(Third Edition)33.Terminology3.1 DefinitionsRefer to the definitions of terms in Termi-nology C717 and Terminology D1566.4.Classification4.1 Types:4.1.1 Type C,intended for use in cold climates(be-low 10C in winter).4.1.2 TypeW,intendedforuseinwarmclimates(above 10C in winter).4.2 GradesGrade designations represent differing degreesof hardne