1、Designation:D259821Standard Practice forCalculation of Certain Physical Properties of LiquefiedPetroleum(LP)Gases from Compositional Analysis1This standard is issued under the fixed designation D2598;the number immediately following the designation indicates the year oforiginal adoption or,in the ca
2、se of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This practice covers,by compositional analysis,theapproximate determination of the following ph
3、ysical charac-teristics of commercial propane,special-duty propane,com-mercial propane/butane mixtures,and commercial butane(cov-ered by Specification D1835):vapor pressure,relative density,and motor octane number(MON).1.1.1 This practice is not applicable to any product exceed-ing specifications fo
4、r nonvolatile residues.(See Test MethodD2158.)1.1.2 For calculating motor octane number,this practice isapplicable only to mixtures containing 20%or less of propene.1.1.3 For calculated motor octane number,this practice isbased on mixtures containing only components shown in Table1.1.2 The values st
5、ated in SI units are to be regarded asstandard.1.2.1 Exceptions:1.2.1.1 Non-SI units in parentheses are given for informa-tion only.1.2.1.2 Motor octane number and relative density are givenin MON numbers and dimensionless units,respectively.1.3 This international standard was developed in accor-dan
6、ce with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standar
7、ds:2D1267 Test Method for Gauge Vapor Pressure of LiquefiedPetroleum(LP)Gases(LP-Gas Method)D1657 Test Method for Density or Relative Density of LightHydrocarbons by Pressure HydrometerD1835 Specification for Liquefied Petroleum(LP)GasesD2158 Test Method for Residues in Liquefied Petroleum(LP)GasesD
8、2163 Test Method for Determination of Hydrocarbons inLiquefied Petroleum(LP)Gases and Propane/PropeneMixtures by Gas ChromatographyD2421 Practice for Interconversion of Analysis of C5andLighter Hydrocarbons to Gas-Volume,Liquid-Volume,orMass Basis2.2 Australian Liquefied Petroleum Gas Association Pu
9、bli-cation:3Liquefied Petroleum Gas for Automotive Use Specification2.3 Gas Processors Suppliers Association:4GPSA Engineering Data Book,12th Edition,20043.Summary of Practice3.1 The composition of a sample of LP-gas is obtained byusing Test Method D2163 or other acceptable method.Fromthe analysis(e
10、xpressed in liquid volume percent),the vaporpressure,relative density,and motor octane number of thesample may be determined.3.2 Conversion of a compositional analysis from mole,gasvolume,or weight basis to liquid volume is obtained by usingPractice D2421 or other suitable method.4.Significance and
11、Use4.1 Vapor pressure is an important specification property ofcommercial propane,special duty propane,propane/butanemixtures,and commercial butane that assures adequatevaporization,safety,and compatibility with commercial appli-ances.Relative density,while not a specification criterion,isnecessary
12、for determination of filling densities and custody1This practice is under the jurisdiction of ASTM Committee D02 on PetroleumProducts,Liquid Fuels,and Lubricants and is the direct responsibility of Subcom-mittee D02.H0 on Liquefied Petroleum Gas.Current edition approved April 1,2021.Published May 20
13、21.Originallyapproved in 1967.Last previous edition approved in 2016 as D2598 16.DOI:10.1520/D2598-21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Docum
14、ent Summary page onthe ASTM website.3Available from Australian Liquefied Petroleum Gas Association Limited,ABN11002703951,30GeorgeStreet,RedfernNSW2016,http:/.au/site/4Available from Gas Processors SuppliersAssociation(GPSA),6526 E.60th St.,Tulsa,OK 74145,http:/www.gpsa.gpaglobal.org.*A Summary of C
15、hanges section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decis
16、ion on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1transfer.The motor octane number(MON)is useful in deter-mining the products suitability as a fuel for internal combus-tion engines.5.Calculation5.1 Calculated LP-Gas Vapor Pressure(see Test MethodD1267):5.1.1 Calculate the partial gauge vapor pressure due to eachcomponent in the mixture as follows:Partial gauge vapor pressure