ImageVerifierCode 换一换
格式:PDF , 页数:17 ,大小:490.50KB ,
资源ID:181069      下载积分:9 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/181069.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_3299_-_18.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_3299_-_18.pdf

1、Designation:D329918An American National StandardStandard Specification forFilament-Wound Glass-Fiber-Reinforced Thermoset ResinCorrosion-Resistant Tanks1This standard is issued under the fixed designation D3299;the number immediately following the designation indicates the year oforiginal adoption o

2、r,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1

3、This specification covers cylindrical tanks fabricated byfilament winding for above-ground vertical installation,tocontain aggressive chemicals at atmospheric pressure as clas-sified herein,and made of a commercial-grade polyester orvinylester resin.Included are requirements for materials,properties

4、,design,construction,dimensions,tolerances,workmanship,and appearance.1.2 This specification does not cover the design of vesselsintended for pressure above atmospheric or under vacuumconditions,except as classified herein,or vessels intended foruse with liquids heated above their flash points.1.3 T

5、he values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4Special design consideration shall be given to tankssubject to environmental and/or mech

6、anical forces such asseismic,wind,ice,agitation,or fluid dynamic forces,tooperational service temperatures greater than 180F(82C)andto tanks with unsupported bottoms.1.5 The following safety hazards caveat pertains only to thetest method portion,Section 11,of this specification:Thisstandard does not

7、 purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.NOTE1There is no known ISO equiva

8、lent to this standard.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization

9、 TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C581 Practice for Determining Chemical Resistance ofThermosetting Resins Used in Glass-Fiber-ReinforcedStructures Intended for Liquid ServiceC582 Specification for Contact-Molded Reinforced Thermo-setting Plastic(RTP

10、)Laminates for Corrosion-ResistantEquipmentD618 Practice for Conditioning Plastics for TestingD883 Terminology Relating to PlasticsD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe,Tubing,and FittingsD2150 Specification for Woven Roving Glass Fabric forPolyester-Glass

11、Laminates(Withdrawn 1987)3D2583 Test Method for Indentation Hardness of Rigid Plas-tics by Means of a Barcol ImpressorD2584 Test Method for Ignition Loss of Cured ReinforcedResinsD2996 Specification for Filament-Wound“Fiberglass”(Glass-Fiber-Reinforced Thermosetting-Resin)PipeD2997 Specification for

12、 Centrifugally Cast“Fiberglass”(Glass-Fiber-Reinforced Thermosetting-Resin)PipeD3892 Practice for Packaging/Packing of PlasticsD4024 Specification for Machine Made“Fiberglass”(Glass-Fiber-Reinforced Thermosetting Resin)FlangesD5421 Specification for Contact Molded“Fiberglass”(Glass-Fiber-Reinforced

13、Thermosetting Resin)FlangesF412 Terminology Relating to Plastic Piping Systems1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.23 on ReinforcedPlastic Piping Systems and Chemical Equipment.Current edition approved Aug

14、.1,2018.Published August 2018.Originallyapproved in 1974.Last previous edition approved in 2010 as D3299 10.DOI:10.1520/D3299-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,r

15、efer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 1942

16、8-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 2.2 ANSI Standards:B 16.1 Cast Iron Pipe Flanges and Flanged Fittings,Class25,125,250,and 80043.Terminology3.1 GeneralDefinitions are in accordance with Terminolo-g

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2