1、Designation:D429421Standard Test Method forSulfur in Petroleum and Petroleum Products by EnergyDispersive X-ray Fluorescence Spectrometry1This standard is issued under the fixed designation D4294;the number immediately following the designation indicates the year oforiginal adoption or,in the case o
2、f revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This test meth
3、od covers the determination of total sulfurin petroleum and petroleum products that are single-phase andeither liquid at ambient conditions,liquefiable with moderateheat,or soluble in hydrocarbon solvents.These materials caninclude diesel fuel,jet fuel,kerosine,other distillate oil,naphtha,residual
4、oil,lubricating base oil,hydraulic oil,crudeoil,unleaded gasoline,gasoline-ethanol blends,biodiesel(seeNote 2),and similar petroleum products.NOTE1Oxygenated fuels with ethanol or methanol contents exceed-ing the limits given in Table 1 can be dealt with using this test method,butthe precision and b
5、ias statements do not apply(see Appendix X3).NOTE2For samples with high oxygen contents(3%by weight)sample dilution as described in 1.3 or matrix matching must be performedto assure accurate results.1.2 Interlaboratory studies on precision revealed the scopeto be 17 mgkg to 4.6%by mass.An estimate o
6、f this testmethods pooled limit of quantitation(PLOQ)is 16.0 mg kg ascalculated by the procedures in Practice D6259.However,because instrumentation covered by this test method can varyin sensitivity,the applicability of the test method at sulfurconcentrations below approximately 20 mg/kg must be det
7、er-mined on an individual basis.An estimate of the limit ofdetection is three times the reproducibility standard deviation,and an estimate of the limit of quantitation2is ten times thereproducibility standard deviation.1.3 Samples containing more than 4.6%by mass sulfur canbe diluted to bring the su
8、lfur concentration of the dilutedmaterial within the scope of this test method.Samples that arediluted can have higher errors than indicated in Section 17 thannon-diluted samples.1.4 Volatile samples(such as high vapor pressure gasolinesor light hydrocarbons)may not meet the stated precisionbecause
9、of selective loss of light materials during the analysis.1.5 Afundamental assumption in this test method is that thestandard and sample matrices are well matched,or that thematrix differences are accounted for(see 6.2).Matrix mis-match can be caused by C/H ratio differences between samplesand standa
10、rds(see Section 6)or by the presence of otherheteroatoms.1.6 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsi
11、bility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization
12、established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D4057 Practice for Manual Sampling of Petroleum andPetroleum P
13、roductsD4175 Terminology Relating to Petroleum Products,LiquidFuels,and LubricantsD4177 Practice for Automatic Sampling of Petroleum andPetroleum ProductsD6259 Practice for Determination of a Pooled Limit ofQuantitation for a Test MethodD6299 Practice for Applying Statistical Quality Assuranceand Co
14、ntrol Charting Techniques to Evaluate AnalyticalMeasurement System PerformanceD7343 Practice for Optimization,Sample Handling,1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.03 on E
15、lemental Analysis.Current edition approved Dec.1,2021.Published December 2021.Originallyapproved in 1983.Last previous edition approved in 2016 as D4294 161.DOI:10.1520/D4294-21.2Analytical Chemistry,Vol 55,1983,pp.2210-2218.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontac
16、t ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theD