1、Designation:D384316(Reapproved 2021)1Standard Practice forQuality Assurance for Protective Coatings Applied toNuclear Facilities1This standard is issued under the fixed designation D3843;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revisio
2、n,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEEditorial updates were made in Section 2 and Section 6 in February 2021.1.Scope1.1 This standard replaces ANSI N101
3、.4 and provides acommon basis for,and specifically comprises quality assurancerequirements applicable to,safety-related protective coatingwork in Coating Service Level I areas of nuclear facilities asdefined in Guide D5144.1.2 This standard meets the requirements of ANSI N101.4while also recognizing
4、 advancements in technology and indus-try practices since transfer to ASTM responsibility forupdating,rewriting,and issuing replacement standards toANSIN101.4.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of
5、 this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the De
6、cision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D4227 Practice for Qualification of Coating Applicators forApplication of Coatings
7、to Concrete SurfacesD4228 Practice for Qualification of Coating Applicators forApplication of Coatings to Steel SurfacesD4537 Guide for Establishing Procedures to Qualify andCertify Personnel Performing Coating and Lining WorkInspection in Nuclear FacilitiesD4538 Terminology Relating to Protective C
8、oating andLining Work for Power Generation FacilitiesD5144 Guide for Use of Protective Coating Standards inNuclear Power Plants2.2 ANSI Standard:3N45.2 Quality Assurance Program Requirements forNuclear Power Plants2.3 ASME Standard:4NQA-1 Quality Assurance Program Requirements forNuclear Facilities2
9、.4 Code of Federal Regulations:510 CFR 50 Appendix B:Title 10,Chapter 1,Energy,Part 50,Domestic Licensing of Production and UtilizationFacilities,Appendix B,Quality Assurance Criteria forNuclear Power Plants and Fuel Reprocessing Plants10 CFR 21 Reporting of Defects and Noncompliances2.5 Other Docum
10、ent:EPRI 1019157 Plant Support Engineering:Guideline onNuclear Safety-Related Coatings,Revision 2(formerlyTR-109937 and 1003102)63.Terminology3.1 DefinitionsDefinitions for use with this standard areshown in Terminology D4538 or other applicable standards.3.2 Definitions of Terms Specific to This St
11、andard:3.2.1 project specification,na written document designedto ensure execution of the coating work for a project in1This practice is under the jurisdiction of ASTM Committee D33 on ProtectiveCoating and Lining Work for Power Generation Facilities and is the directresponsibility of D33.04 on Qual
12、ity Systems and Inspection.Current edition approved Feb.1,2021.Published February 2021.Originallyapproved in 1980.Last previous edition approved in 2016 as D3843 16.DOI:10.1520/D3843-16R21E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at servic
13、eastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.4Available from American Society of Mechanical Engine
14、ers(ASME),ASMEInternational Headquarters,Two Park Ave.,New York,NY 10016-5990,http:/www.asme.org.5Available from U.S.Government Printing Office Superintendent of Documents,732 N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401,http:/www.access.gpo.gov.6Available from EPRI,3420 Hillview Ave.,Palo Alt
15、o,CA 94304,http:/.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelop
16、ment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1accordance with the licensees requirements.It is usuallycomprised of the general,legal,and technical specificationsgoverning the work.4.Significance and Use4.1 Quality assurance,as covered by this practice,com-prises all those planned and systematic actions necessary toprovide adequate confidence that safety-related coating work innuclear facilities as def