1、Designation:D178198(Reapproved 2012)Standard Test Method forClimbing Drum Peel for Adhesives1This standard is issued under the fixed designation D1781;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number
2、 in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method covers the determination of the peelresista
3、nce of adhesive bonds between:a relatively flexibleadherend and a rigid adherend;and the relatively flexiblefacing of a sandwich structure and its core,when tested underspecified conditions.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for in
4、formationonly.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Re
5、ferenced Documents2.1 ASTM Standards:2B209 Specification for Aluminum and Aluminum-AlloySheet and PlateD907 Terminology of AdhesivesE4 Practices for Force Verification of Testing Machines2.2 ASTM Adjuncts:Climbing Drum Peel Tester33.Terminology3.1 DefinitionsMany of the terms used in this test metho
6、dare defined in Terminology D907.4.Summary of Test Method4.1 Determine the peeling force of a conditioned adhesivebonded sandwich assembly by peeling a face skin around acircular drum.This is done by clamping the assembly in auniversal test machine.The average peeling load is determinedusing a stand
7、ard formula.5.Significance and Use5.1 This test method may be used to determine comparativerather than fundamental measurements of adhesion and isparticularly suitable for process control,some examples ofwhich are listed.5.1.1 This test method is particularly sensitive to adherendsurface preparation
8、 and is of value where the adhesive is usedin conjunction with a primer.5.1.2 When a relatively brittle adhesive is used,the peelresistance can often give an indication of the degree of cure,that is,higher values than normally realized may indicate anincomplete cure.Direct comparison of different ad
9、hesives orprocesses can only be made when specimen design and testconditions are identical.6.Apparatus6.1 Peeling Apparatus,consisting of a flanged drum,flex-ible loading straps or cables,and suitable clamps for holdingthe test specimen.The apparatus illustrated in Fig.1 has beenfound to be satisfac
10、tory.6.1.1 The outside radius of the drum is 51.00 6 0.13 mm(2.000 6 0.005 in.),and the radius of the flange,including onehalf of the thickness of the loading straps or cables,is 12.70 60.13 mm(0.500 6 0.005 in.)larger than the radius of the drum.This 12.70 6 0.13 mm(0.500 6 0.005 in.)less half thet
11、hickness of the adherend to be peeled,is the effective torquearm of the apparatus.6.1.2 Use a suitable top clamp(Fig.2)for supporting thespecimen,and a drum clamp(Fig.3)to hold the adherendagainst the face of the drum.6.1.3 Balance the drum about the axis by the use ofcounterweights(as shown in Fig.
12、1)placed diametricallyopposite the drum clamp to compensate for the weight of thisclamp.1This test method is under the jurisdiction of ASTM Committee D14 onAdhesives and is under the jurisdiction of Subcommittee D14.80 on Metal BondingAdhesives.Current edition approved May 1,2012.Published May 2012.
13、Originallyapproved in 1960.Last previous edition approved in 2004 as D1781 98(2004).DOI:10.1520/D1781-98R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards
14、 Document Summary page onthe ASTM website.3Detailed working drawings for the apparatus illustrated are available fromASTM International Headquarters.Order Adjunct No.ADJD1781.Original adjunctproduced in 1960.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-29
15、59.United States1 6.1.4The drum and flanges with the drum clamp and itscompensating weight weighs 3.6 kg(8 lb),a lighter weightbeing preferable to facilitate handling of the apparatus.4,36.2 Testing Machine,capable of applying tensile loadsunder the conditions prescribed in Section 11 and with thefo
16、llowing further requirements:6.2.1 The rate of movement between heads of the testingmachine remains essentially constant under fluctuating loads(Note 1).6.2.2 The testing machine weighs the load to within 1%.The testing machine and range are selected such that themaximum load on the specimen falls between 15 and 85%ofthe full-scale capacity.6.2.3 The use of autographic equipment to record loadversus head movement is recommended.6.2.4 Verification of the testing machine is made in accor-dance wit