ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:59.96KB ,
资源ID:181593      下载积分:10 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/181593.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_2203_-_01_2011.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_2203_-_01_2011.pdf

1、Designation:D220301(Reapproved 2011)Standard Test Method forStaining from Sealants1This standard is issued under the fixed designation D2203;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parent

2、heses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers a laboratory procedure fordetermining whether a sample of sealant will cause staining ofthe substrate when in the contact with maso

3、nry,concrete,orstone(marble,limestone,sandstone,granite,etc.).1.2 The values stated in SI(metric)units are to be regardedas the standard.The values given in parentheses are providedfor information only.1.3 This standard does not purport to address all of thesafety problems,if any,associated with its

4、 use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE1Currently there is no ISO standard similar to this test method.2.Referenced Documents2.1 ASTM Standards:2C510 T

5、est Method for Staining and Color Change of Single-or Multicomponent Joint SealantsC717 Terminology of Building Seals and Sealants3.Terminology3.1 DefinitionsRefer to Terminology C717 for definitionsof the following terms used in this test method:compound,sealant,substrate.4.Significance and Use4.1

6、Staining of a building is an aesthetically undesirableoccurrence.This test method evaluates the likelihood of asealant causing an early stain on a porous substrate,when thestain is caused by gross exudation from the sealant.This testmethod does not predict staining caused by other factors.4.2 See al

7、so Test Method C510.5.Apparatus and Materials5.1 Convection Oven,having a temperature controlled at104.5 6 3C(220 6 5F).5.2 Brass Ring,19 mm(34in.)inside diameter,19 mm(34in.)high,walls at one end beveled to a minimum diameter.5.3 Filter Paper,ten sheets,high-grade,rapid,qualitative 9cm in diameter.

8、35.4 Aluminum Foil,household-type,25.4 mm(1 in.)square.5.5 Weight,300-g.5.6 Spatula,small,thin,steel.5.7 Glass Plate,at least 100 by 100 mm(4 by 4 in.).5.8 Desiccator,with drying agent.6.Sampling6.1 Take the test specimen from a previously unopenedcontainer and thoroughly mix before using,if require

9、d forhomogeneity.7.Conditioning7.1 Condition the sample in a closed container for at least 5h at 23 6 2C(73.4 6 3.6F).8.Procedure8.1 Dry the filter papers for 5 to 8 h in an oven maintainedat 104.5 6 3C(220 6 5.4F).At the end of the drying period,remove from the oven and store in a desiccator until

10、cool.8.2 Remove ten filter papers from the desiccator,staplethem together,and place them on a glass plate.Set the brassring with beveled edge down on the center of the filter papers.Fill the ring flush with thoroughly mixed sealant,taking care toincorporate as little air as possible with the compoun

11、d.Place a25.4-mm(1-in.)square piece of aluminum foil on top of thering,and the 300-g weight on top of that.8.3 Allow the filled ring to stand for 72 h at 23 6 2C(73.46 3.6F).Then slide a spatula under the brass ring and removethe ring and compound.Hold the top filter paper up to the lightwith a glas

12、s plate under it and,with a sharp pencil,mark the1This test method is under the jurisdiction ofASTM Committee C24 on BuildingSeals and Sealants and is the direct responsibility of Subcommittee C24.20 onGeneral Test Methods.Current edition approved June 1,2011.Published August 2011.Originallyapproved

13、 in 1963.Last previous edition approved in 2007 as D2203 01(2007).DOI:10.1520/D2203-01R11.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary

14、page onthe ASTM website.3This test method is based on the use of Whatman No.1 filter paper,manufactured by Whatman,Inc.,9 Bridewell Place,Clifton,NJ 07073.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 maximum and minimum diameters of th

15、e stain.Measure thesediameters to the nearest 0.5 mm.Subtract 19(diameter of ringin millimetres)from the average of the two diameters anddivide by 2.Record this result as width of stain.(Width ofstain=(average 19)/2).8.4 Examine the ten individual papers for depth of stain byholding them up to a lig

16、ht.Record the number of papers,including the first one,showing any evidence of staining asnumber of papers stained.8.5 Report the sum of width of stain and number of papersstained as the stain index.9.Alternative Procedure9.1 If the sample or compound to be tested is accompaniedby a sample block of masonry(brick,marble,limestone,etc.)on which it is to be used,the standard procedure shall bewaived and the following alternative test used in its place:9.1.1 Dry duplicate specimens of the masonry sa

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2