ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:73.15KB ,
资源ID:181613      下载积分:10 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/181613.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_2213_-_00_2020.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_2213_-_00_2020.pdf

1、Designation:D221300(Reapproved 2020)Standard Test Method forCompressibility of Leather1This standard is issued under the fixed designation D2213;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in pa

2、rentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method covers the determination of the com-pressibility

3、of sole leather.This test method does not apply towet blue.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not

4、purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard

5、 was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Reference

6、d Documents2.1 ASTM Standards:2D1610 Practice for Conditioning Leather and Leather Prod-ucts for TestingD1813 Test Method for Measuring Thickness of LeatherTest Specimens3.Terminology3.1 Definitions:3.1.1 compressibilitythe percentage change in thicknessof a specimen on being subjected to a specifie

7、d pressure for aperiod of time.4.Summary of Test Method4.1 A load of 12 000 lbf(53 kN)or 3000 psi(21 MPa)isapplied to a leather specimen 2 by 2-in.2(51 by 51-mm2).Thepercentage change in initial thickness,determined by measur-ing thicknesses before and after compression,represents thecompressibility

8、 of the sample.5.Significance and Use5.1 Compressibility is considered an important factor thatinfluences wear resistance of sole leather.3,46.Apparatus6.1 Press,5either hand-or power-driven,having a capacityof at least 15 000 lbf(67 kN)permitting a pressure of 3000 6100 psi(21 6 1 MPa).The rate of

9、increase shall not exceed200 psi/s(1.4 MPa/s).The press shall contain two flat steelplates and an indicator for reading the applied force.A suitabletesting machine may also be used.6.2 Stop Watch,or other suitable timing device.7.Test Specimen7.1 The specimen shall be a square of leather 2 by 2 6132

10、in.(51 by 51 6 0.8 mm)cut by a die.8.Procedure8.1 Condition the specimens in accordance with PracticeD1610.8.2 Measure the initial thickness of the specimen at themiddle of each side approximately 0.5 in.(12.7 mm)from theedge in accordance with Method D1813 averaged and recordedas T1.1This test meth

11、od is under the jurisdiction of ASTM Committee D31 on Leatherand is the direct responsibility of Subcommittee D31.01 on Vegetable Leather.Thistest method was developed in cooperation with the American Leather ChemistsAssn.(Standard Method E45 1953).Current edition approved Dec.1,2020.Published Decem

12、ber 2020.Originallyapproved in 1963.Last previous edition approved in 2016 as D2213 00(2016).DOI:10.1520/D2213-00R20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the

13、standards Document Summary page onthe ASTM website.3Hobbs,R.B.,and Kronstadt,R.A.,Journal of the American Leather ChemistsAssociation JALCA.,Vol 40,1945,p.12.4Booth,W.E.,Journal of the Society of Leather Trades Chemists,Vol 43,1959,p.3495The sole source of supply of the hand press known to the commi

14、ttee at this timeis Fred S.Carver Co.,Summit,NJ.If you are aware of alternative suppliers,pleaseprovide this information to ASTM Headquarters.Your comments will receivecareful consideration at a meeting of the responsible technical committee,1whichyou may attend.Copyright ASTM International,100 Barr

15、 Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendati

16、ons issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.8.3 Place the specimen between the flat steel plates andapply pressure at a rate not greater than 200 psi/s(1.4 MPa/s)until the required 3000 6 100 psi(21 6 1 MPa)is reached.NOTE1The operator shall take care to apply the force uniformly andperpendicular to the leather surfaces.8.4 Maintain the load for 3 min,continuously correcting forrelaxation or loss in force,and then release.8.5 Remove the specimen from the

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2