1、Designation:D1555M22Standard Test Method forCalculation of Volume and Weight of Industrial AromaticHydrocarbons and Cyclohexane Metric1This standard is issued under the fixed designation D1555M;the number immediately following the designation indicates the year oforiginal adoption or,in the case of
2、revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This standard is for use in calculating the weight andvolume of benzene,toluene,mixed xylenes,styrene
3、,ortho-xylene,meta-xylene,para-xylene,cumene,ethylbenzene,148.9to176.7 Cand176.7to204.4 Caromatichydrocarbons,and cyclohexane.A method is given for calcu-lating the volume at a given temperature from an observedvolume at an observed temperature,t C.Table 1 lists thedensity in Vacuo at 15 F and 20 C
4、for chemicals used todevelop the relationship.Densities(or weights)“in vacuo”represent the true density(or weight)if measured in a vacuumwithout the buoyancy effect of air acting on the liquid.It isrepresentative of the actual amount of product present.Densi-ties(or weights)“in air”represent what wo
5、uld be measured ona scale.The difference is on the order of 0.13%.Moderndensitometers measure density in vacuo and the ASTM recom-mends the use of in vacuo densities(or weights).1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard
6、.1.2.1 A complete inch-pound unit companion standard hasbeen developed in Test Method D1555.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environm
7、ental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,
8、Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1217 Test Method for Density and Relative Density(Spe-cific Gravity)of Liquids by Bingham PycnometerD1555 Test Method for Calculation of Volume and W
9、eightof Industrial Aromatic Hydrocarbons and CyclohexaneD3505 Test Method for Density or Relative Density of PureLiquid ChemicalsD4052 Test Method for Density,Relative Density,and APIGravity of Liquids by Digital Density Meter2.2 Other Documents:American Petroleum Society Research Project 443Patters
10、on,J.B.,and Morris,E.C.,Metrologia,31,1994,pp.277-288TRC Thermodynamic TablesHydrocarbons,NSRDS-NIST 75-121,Supplement No.121,April 30,200143.Significance and Use3.1 This test method is suitable for use in calculatingweights and volumes of the products outlined in Section 1.Theinformation presented
11、in this method can be used for deter-mining quantities of the above-stated aromatic hydrocarbons intanks,shipping containers,etc.4.Basic Data4.1 Densities of materials should be determined by mea-surement(see Section 7).Densities of pure materials at 60 Fmay be estimated from densities furnished by
12、NSRDS-NIST75-121(National Standard Reference Data SeriesNationalInstitute of Standards and Technology).4.2 The VCF(Volume Correction Factor)equations pro-vided below are derived from the Volume Correction imple-mentation procedures presented in Method D1555.1This test method is under the jurisdictio
13、n of ASTM Committee D16 onAromatic,Industrial,Specialty and Related Chemicals and is the direct responsi-bility of Subcommittee D16.01 on Benzene,Toluene,Xylenes,Cyclohexane andTheir Derivatives.Current edition approved Sept.1,2022.Published September 2022.Originallyapproved in 1993.Last previous ed
14、ition approved in 2016 as D1555M 16.DOI:10.1520/D1555M-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3“Select
15、ed Values of Properties of Hydrocarbons and Related Compounds,”prepared by American Petroleum Institute Research Project 44 at the ChemicalThermodynamics Center,Department of Chemistry,Texas A&M,College Station,TX.4Available from National Institute of Standards and Technology(NIST),100Bureau Dr.,Sto
16、p 1070,Gaithersburg,MD 20899-1070,http:/www.nist.gov.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Te