ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:73.82KB ,
资源ID:182526      下载积分:11 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/182526.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_1516_-_05_2021.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_1516_-_05_2021.pdf

1、Designation:D151605(Reapproved 2021)Standard Test Method forWidth of Leather1This standard is issued under the fixed designation D1516;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses

2、indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method covers determination of the width ofphysical test specimens

3、 and of regularly shaped units andpieces of all types of leather.This test method does not applyto wet blue.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are no

4、t considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitat

5、ions prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization Tec

6、hnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1610 Practice for Conditioning Leather and Leather Prod-ucts for Testing3.Significance and Use3.1 This test method is designed to measure the width ofspecimens before and after they are subjected to various testswhich m

7、ay change the width.A test procedure wherein suchmeasurements could be used is the change in area of squarepieces when measuring the resistance of leather to syntheticperspiration solution.4.Apparatus4.1 Steel Scale,graduated to 0.02 in.(0.5 mm).4.2 Steel Tape,graduated to116in.or in millimetres.5.S

8、pecimen5.1 The specimen shall be the prepared test specimen,unit,or piece.It shall be conditioned for 48 h in an atmospheremaintained at 73.4 6 1.8 F(23 6 1 C)and 50 6 4%relativehumidity and tested under these conditions.See PracticeD1610.6.Procedure6.1 Test SpecimensPlace the specimen on a flat sur

9、faceand flatten it out without pulling or stretching.Measure thewidth to the nearest 0.02 in.(0.5 mm)at the locationsdesignated in the test method for making the particular test forwhich the specimen was prepared.7.Calculation and Report7.1 Report the width of the test specimens used as pre-scribed

10、in the test method for making the particular physicaltest for which the specimen was prepared.7.2 Report the average of the width measurements taken onany unit or piece to the same accuracy as observed on theoriginal measurements,as the width of the piece.8.Precision and Bias38.1 The following crite

11、ria may be used to judge the accept-ability of results if at least 15 units have been tested.8.2 A coefficient of variation of 1.8%can be expectedbetween laboratories on specimens of headband leather sub-jected to a perspiration test.NOTE1The data used as a basis for this reproducibility statement w

12、asobtained on a round robin with 3 laboratories measuring width on the1This test method is under the jurisdiction of ASTM Committee D31 on Leatherand is the direct responsibility of Subcommittee D31.07 on Physical Properties Thistest method has been developed in cooperation with theAmerican Leather

13、ChemistsAssn.(Standard Method E5-1961).Current edition approved Sept.1,2021.Published October 2021.Originallyapproved in 1957.Last previous edition approved in 2017 as D1516 05(2017).DOI:10.1520/D1516-05R21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Se

14、rvice at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Supporting data for the reproducibility statement are filed at ASTM Headquar-ters and may be obtained by requesting Research Report RR:D31-1007.Copyright ASTM

15、 International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,

16、Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1same specimens.The specimens were 51 mm by 51 mm before theperspiration testing.8.3 BiasNo justifiable statement on bias can be madesince the true value of width of leather test specimens cannotbe established by an accepted reference method.9.Keywords9.1 area change;leather;widthASTM International takes no position respecting the validity of any patent rights asserted in connection with a

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2