1、Designation:D216810(Reapproved 2018)Standard Practices forCalibration of Laboratory Mechanical-Rammer SoilCompactors1This standard is issued under the fixed designation D2168;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year o
2、f last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 These practices for the calibration
3、of mechanical soilcompactors are for use in checking and adjusting mechanicaldevices used in laboratory compacting of soil and soil-aggregate in accordance with Test Methods D698,D1557,Practice D6026,and other methods of a similar nature thatmight specify these practices.Calibration for use with one
4、practice does not qualify the equipment for use with anotherpractice.1.2 The weight of the mechanical rammer is adjusted asdescribed in 5.4 and 6.5 in order to provide for the mechanicalcompactor to produce the same result as the manual compactor.1.3 Two alternative procedures are provided as follow
5、s:SectionPractice ACalibration based on the compaction of aselected soil sample5Practice BCalibration based on the deformation of astandard lead cylinder61.4 If a mechanical compactor is calibrated in accordancewith the requirements of either Practice A or Practice B,it isnot necessary for the mecha
6、nical compactor to meet therequirements of the other practice.1.5 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.1.5.1 It is common practice in the engineering profession toconcurrently use pounds to represent both a un
7、it of mass(lbm)and a force(lbf).This implicitly combines two separatesystems of units;that is,the absolute system and the gravita-tional system.It is scientifically undesirable to combine the useof two separate sets of inch-pound units within a singlestandard.This standard has been written using the
8、 gravitationalsystem of units when dealing with the inch-pound system.Inthis system,the pound(lbf)represents a unit of force(weight).However,the use of balances or scales recording pounds ofmass(lbm)or the recording of density in lbm/ft3shall not beregarded as a nonconformance with this standard.1.6
9、 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.7 Thi
10、s international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(T
11、BT)Committee.2.Referenced Documents2.1 ASTM Standards:2D653 Terminology Relating to Soil,Rock,and ContainedFluidsD698 Test Methods for Laboratory Compaction Character-istics of Soil Using Standard Effort(12,400 ft-lbf/ft3(600kN-m/m3)D1557 Test Methods for Laboratory Compaction Character-istics of So
12、il Using Modified Effort(56,000 ft-lbf/ft3(2,700 kN-m/m3)D2487 Practice for Classification of Soils for EngineeringPurposes(Unified Soil Classification System)D3740 Practice for Minimum Requirements for AgenciesEngaged in Testing and/or Inspection of Soil and Rock asUsed in Engineering Design and Co
13、nstructionD6026 Practice for Using Significant Digits in GeotechnicalDataE11 Specification for Woven Wire Test Sieve Cloth and TestSievesE145 Specification for Gravity-Convection and Forced-Ventilation Ovens1These practices are under the jurisdiction ofASTM Committee D18 on Soil andRock and are the
14、direct responsibility of Subcommittee D18.03 on Texture,Plasticity and Density Characteristics of Soils.Current edition approved July 1,2018.Published July 2018.Originally appr-roved in 1990.Last previous edition approved in 2010 as D216810.DOI:10.1520/D2168-10R18.2For referenced ASTM standards,visi
15、t the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Bar
16、r Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.Significance and Use3.1 Mechanical compactors are commonly used to replacethe hand compactors required for Tes