1、Designation:D223922An American National StandardStandard Specification forPolyethylene(PE)Plastic Pipe(SIDR-PR)Based onControlled Inside Diameter1This standard is issued under the fixed designation D2239;the number immediately following the designation indicates the year oforiginal adoption or,in th
2、e case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This s
3、pecification covers polyethylene(PE)pipe madeto standard inside dimension ratios(SIDR)and pressure ratedfor water(see appendix).Included are requirements for PEcompoundsandrequirementsandtestmethodsforworkmanship,dimensions,elevated temperature sustainedpressure,burst pressure,and marking.NOTE1Refer
4、 to specificationAWWAC901and PPI Technical Note 49(TN-49)for further information on pipe suitability for potable water enduse applications.Oxidative Resistance Classification(CC#rating)infor-mation is available from NSF International.1.2 The values stated in inch-pound units are to be regardedas sta
5、ndard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 The text of this specification references notes,footnotes,and appendixes which provide explanatory material.Thesenotes and footnotes shall not be co
6、nsidered as requirements ofthe specification.Notes and footnotes in tables and figures,andSupplementary Requirements are requirements of the specifi-cation.1.4 The following safety hazards caveat pertains only to thetest methods portion,Section 7,of this specification:Thisstandard does not purport t
7、o address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.5 This international standard was develop
8、ed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2
9、.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD1238 Test Method for Melt Flow Rates of Thermoplasticsby Extrusion PlastometerD1598 Test Method for Time-to-Failure of Plastic PipeUnder Constant Internal PressureD1599 Test Meth
10、od for Resistance to Short-Time HydraulicPressure of Plastic Pipe,Tubing,and FittingsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1603 Test Method for Carbon Black Content in OlefinPlasticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2565 Practice
11、for Xenon-Arc Exposure of Plastics In-tended for Outdoor ApplicationsD2837 Test Method for Obtaining Hydrostatic Design Basisfor Thermoplastic Pipe Materials or Pressure Design Basisfor Thermoplastic Pipe ProductsD3350 Specification for Polyethylene Plastics Pipe and Fit-tings MaterialsD4218 Test Me
12、thod for Determination of Carbon BlackContent in Polyethylene Compounds by the Muffle-Furnace TechniqueF412 Terminology Relating to Plastic Piping SystemsF2263 Test Method for Evaluating the Oxidative Resistanceof Polyethylene(PE)Pipe to Chlorinated WaterG154 Practice for Operating Fluorescent Ultra
13、violet(UV)Lamp Apparatus for Exposure of Nonmetallic MaterialsG155 Practice for Operating XenonArc LampApparatus forExposure of Materials2.2 APWA Standard:3APWA Uniform Color Code1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibi
14、lity of Subcommittee F17.26 on OlefinBased Pipe.Current edition approved Nov.1,2022.Published November 2022.Originallyapproved in 1964.Last previous edition approved in 2021 as D2239 21.DOI:10.1520/D2239-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Se
15、rvice at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3APWA,2345 Grand Boulevard,suite 500,Kansas,City,MO 64108-2641.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,10
16、0 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.12.3 AWWA Standards:4C901 Polyethylene(PE)Pressure Pipe and Tubing,34in.(19mm)through 3 in.(76 mm),for Water