1、Designation:D 1749 93(Reapproved 2002)An American National StandardTechnical Association of the Pulpand Paper IndustryStandard Method T 1200 osStandard Practice forInterlaboratory Evaluation of Test Methods Used with Paperand Paper Products1This standard is issued under the fixed designation D 1749;
2、the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scop
3、e1.1 The purpose of an interlaboratory study is to determinethe variability in results caused by differences among labora-tories following a prescribed test method,the consistency frommaterial to material of this variability,and the type of addi-tional standardization needed,if any.The study may be
4、madeto obtain information for improving the test method or to arriveat an estimate of the precision of an existing method forpublication.It may also include a comparison of alternative testmethods.1.2 To achieve the objectives in 1.1 satisfactorily,it isessential that a sound statistical design be e
5、mployed in theplanning of an interlaboratory study.This practice gives thebasic principles involved in the planning in order to make thedata amenable to statistical analysis and interpretation.1.3 This practice has been written for the task groupchairman responsible for the preparation or the revisi
6、on of astandard test method.It tells him what information he needs inorder to properly plan an interlaboratory study(Sections 1-10),it outlines the procedure for conducting the study(Section 11),and it gives him background information for understanding theanalysis(Section 12)and interpretation(Secti
7、ons 13-15)of theresults.1.4 While the services of a statistician are not absolutelynecessary for the design,analysis,and interpretation of inter-laboratory studies,questions often arise that could be readilyanswered by a statistician familiar with the analysis usedherein.Hence,the task group chairma
8、n should arrange when-ever possible to consult with a statistician both during theplanning and during the analysis and interpretation.1.5 This practice is similar to TAPPI T1200,which detailsthe analysis using a set of typical data.1.6 This standard does not purport to address all of thesafety conce
9、rns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:D 685 Practice for Conditioning Paper and Pap
10、er Productsfor Testing2E 177 Practice for Use of the Terms Precision and Bias inASTM Test Methods3E 178 Practice for Dealing With Outlying Observations3E 456 Terminology Relating to Quality and Statistics3E 691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Meth
11、od32.2TAPPI Standards:T 402 Standard conditioning and testing atmospheres forpaper,board,pulp handsheets,and related products4T 1200Interlaboratory evaluation of test methods todetermine TAPPI repeatability and reproducibility4T 1205 Dealing with outlying test results4OUTLINE OF RECOMMENDED PROCEDUR
12、E3.Formulating the Problem3.1 If the objective of the task group was not clearly spelledout when the task group was established,determine this by taskgroup discussion,and obtain approval from the chairman of theparent committee(Annex A1.1).3.2 Refer to Terminology E 456 for terminology.4.Preliminary
13、 Study Within One Laboratory4.1 Investigate the several variables of the test method,bothexperimentally and theoretically,including the following(seealso A1.2.1-A1.2.3).4.1.1 Survey the literature and other sources of informationfor possible sources of variability in the application of the testmetho
14、d.4.1.2 Determine how the result of measurement is affectedby variations in the critical dimensions of instruments orcritical steps in the procedure.4.1.3 Determine how the result is affected by known varia-tions in atmospheric conditions,unknown differences betweenoperators,and by other variables.1
15、This practice is under the jurisdiction of ASTM Committee D06 on Paper andPaper Products and is the direct responsibility of Subcommittee D06.92 on TestMethods.Current edition accepted Sept.15,1993.Published November 1993.Originallyapproved in 1960.Last previous edition approved in 1988 as D 1749 68
16、(1988)e1.2Annual Book of ASTM Standards,Vol 15.09.3Annual Book of ASTM Standards,Vol 14.02.4Available from the Technical Association of the Pulp and Paper Industry,P.O.Box 105113,Atlanta,GA 30348.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.4.2 Select what appears to be the optimum procedure.Achoice between two procedures may be made using the“sensitivity criterion”(Annex A2).4.3 Using papers with a wide range of values of the prop