1、Designation:D190006(Reapproved 2015)Standard Practice forCarbon BlackSampling Bulk Shipments1This standard is issued under the fixed designation D1900;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number
2、 in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice covers procedures for the sampling anddata reporting of bulk shipments of carbon black in three-compartment hopper rail cars and co
3、mpartmented bulk hoppertrailers.NOTE1The tests to be made on the samples obtained by this practice,how many samples are taken,where they are taken,and what statisticalvalues(if any)to report shall be determined by agreement between thepurchaser and the manufacturer.This practice gives guidance for u
4、se indeveloping such agreements or for use when no formal agreement exists.The specific details of each procedure are described in appropriate ASTMtest methods used for testing carbon black.NOTE2Some purchasers or manufacturers may consider FlexibleIntermediate Bulk Containers(FIBC)to be a bulk ship
5、ment.See PracticeD1799 for guidance on sampling and reporting for this package.1.2 The values stated in SI units are to be regarded asstandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its us
6、e.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D1799 Practice for Carbon BlackSampling PackagedShipmentsD5817 Practice for C
7、arbon Black,PelletedReduction,Blending,and Drying of Gross Samples for Testing3.Significance and Use3.1 Sampling of bulk shipments of carbon blacks is ofutmost importance since the location and number of samplestaken by different laboratories can have a significant effect onthe agreement of test val
8、ues obtained.This practice is for usein obtaining representative samples of carbon black in eachcompartment or in the entire hopper car or hopper truck.Thesesamples may be used to ascertain the average quality or theuniformity of a shipment,or both.4.Sampling Procedure4.1 Withdraw approximately a 4
9、dm3(1 gal)sample fromeach sample port,after first withdrawing at least 4 dm3(1 gal)of carbon black from each port and discarding it.Sample portsare located on each side of each compartment in a three-compartment bulk hopper rail car and on one side of a hoppertruck.4.2 If sampling from the top ports
10、 of a hopper car or hoppertruck,approximately 150 mm(6 in.)of surface material shouldbe raked aside before collecting approximately 4 dm3(1 gal)for testing.4.3 Asample thief may be used to sample from the top portsof a hopper car or hopper truck.The thief must be able tosample at least 150 mm(6 in.)
11、below the surface.Collectapproximately 4 dm3(1 gal)for testing.4.4 If sampling a hopper car or hopper truck during unload-ing it is recommended that three samples be collected fortesting from each compartment:one at the beginning ofunloading,one at approximately the middle of unloading,andone near t
12、he end of unloading.The sample size should beapproximately 4 dm3(1 gal).4.5 If sampling a hopper car or hopper truck during loadingit is recommended that three samples be collected for testingfrom each compartment:one at the beginning of loading,oneat approximately the middle of loading and one near
13、 the end ofloading.The sample size should be approximately 4 dm3(1 gal).4.6 Samples collected as described in 4.1 4.5 may betested singly or composited.See Practice D5817 for guidanceon preparing composited samples.When disputed test resultsarise reasonable efforts should be made for all parties to
14、testsamples taken from the same location.5.Sample Preparation and Handling5.1 Store the samples in airtight containers until the mate-rials are needed for sample preparation or testing.Hold any1This practice is under the jurisdiction of ASTM Committee D24 on CarbonBlack and is the direct responsibil
15、ity of Subcommittee D24.61 on Carbon BlackSampling and Statistical Analysis.Current edition approved Nov.1,2015.Published December 2015.Originallyapproved in 1961.Last previous edition approved in 2011 as D1900 06(2011).DOI:10.1520/D1900-06R15.2For referenced ASTM standards,visit the ASTM website,ww
16、w.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 excess material in airtight containers for possible follow-uptesting until all tests are completed.5.2 Handle samples collected for the determination of pelletquality with care to avoid pellet breakdown.5.3 Ifind