1、Designation:D 1931 99(Reapproved 2004)An American National StandardStandard Specification forFully Cured Silicone Rubber-Coated Glass Fabric and Tapesfor Electrical Insulation1This standard is issued under the fixed designation D 1931;the number immediately following the designation indicates the ye
2、ar oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers fully cured silicone rubber-coated
3、 glass fabric in sheet form,full-width rolls,and tapes tobe used as electrical insulation.2.Referenced Documents2.1 ASTM Standards:2D 618 Practice for Conditioning Plastics for TestingD 1458 Test Methods for Fully Cured Silicone Rubber-Coated Glass Fabric and Tapes for Electrical InsulationD 1711 Te
4、rminology Relating to Electrical Insulation3.Terminology3.1 Definitions:3.1.1 For definitions of terms used in this specification,referto Terminology D 1711.4.Ordering Information4.1 Orders for material covered by this specification shallinclude the following information:4.1.1 Form(see Section 1),4.
5、1.2 Desired nominal thickness,width,length,or weight,4.1.3 Number of rolls per package,4.1.4 Marking of packages,and,4.1.5 Whether mica dusting is required or not.5.Materials and Manufacture5.1 The glass fabric and the silicone rubber shall be of goodcommercial quality and shall be such as to produc
6、e a productthat will meet the requirements of this specification.Thesurface of the coated fabric shall be free of blisters,the coatedfabric shall be free of wrinkles and creases,and the goods shallbe free of any dust or dirt such as might be picked up due to astatic charge during processing.5.2 The
7、material shall not be spliced unless agreed upon bythe purchaser and the manufacturer.If necessary to splice,thefollowing criteria may be used as a guide:in any givenshipment,90%should have no splice;the remaining 10%may have one splice and this should be flagged.The manner ofsplicing shall be agree
8、d upon between the purchaser and theseller.6.Dimensional Requirements(Finished Cloth)6.1 WidthFull-width rolls and sheets shall be 91 6 2 cm(36 6 1 in.)in width,and shall be supplied trimmed to not lessthan 89 cm(35 in.)wide,unless otherwise specified.Individualmeasurements on tapes shall vary not m
9、ore than 0.8 mm(132in.)from the specified width for tapes 38 mm(112in.)or lessin width,nor more than 1.6 mm(116in.)for tapes over 38 mmin width.6.2 LengthThe nominal length or weight shall be asspecified in the purchase order.The measured lengths ofindividual rolls or sheets shall be not less than t
10、hat specified.7.Test Methods7.1 Appropriate sampling and test methods conforming toTest Methods D 1458 shall be used to determine the confor-mity of materials to this specification.8.Physical and Electrical Requirements8.1 The properties of the silicone rubber-coated glass fabricand tapes shall conf
11、orm to those prescribed in Table 1.9.Rejection and Rehearing9.1 The purchaser reserves the right to reject any part of theshipment that does not conform to the requirements forpackaging and marking as specified in Section 10.9.2 The failure of 20%or more of the sample rolls or sheetsto conform to an
12、y one of the requirements given in Sections 5,6,7,and 8 shall constitute cause for rejection of the entireshipment without further tests.1This specification is under the jurisdiction of ASTM Committee D09 onElectrical and Electronic Insulating Materials and is the direct responsibility ofSubcommitte
13、e D09.07 on Flexible and Rigid Insulating Materials.Current edition approved Oct.10,1999.Published November 1999.Originallyapproved in 1961.Last previous edition approved in 1994 as D 1931 94.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at servic
14、eastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.9.3 The failure of a sample roll to conform to the require-ments
15、 of one or more of the sections noted in 9.2 shall becounted as only one roll failure.10.Packaging and Package Marking10.1 PackagingRolls of silicone rubber-coated glass fab-ric,either in fullwidth rolls or slit tape form,shall bewrapped in such manner as to maintain the rolls in a firm andcompact c
16、ondition and to protect the contents of the packagefrom mechanical damage,moisture,and contamination duringshipment.Sheets shall be packaged with equal care forprotection during shipment.10.2 MarkingShipping containers shall be marked withthe name of the manufacturer,catalog number,lot number,color,thickness,width,yardage,or weight,and date ofmanufacture.11.Keywords11.1 electrical insulation;silicone rubber-coated glass fabricASTM International takes no position respecting the validity of any pa