1、Designation:D220017(Reapproved 2021)Swedish Standards AssociationStandard SIS 05 59 00ISO 8501SSPC:The Society for Protective CoatingsSSPC VIS 1,VIS 3,VIS 4/NACE VIS 7,VIS 5/NACE VIS 9Danish Standards AssociationDanish Standard DS 2019European Committee of Paint and PrintingInk Manufacturers Associa
2、tionStandard Practice forUse of Pictorial Surface Preparation Standards and Guidesfor Painting Steel Surfaces1This standard is issued under the fixed designation D2200;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last
3、revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 The visual surface preparation guides and s
4、tandardsconsist of a series of color prints available as separatepublications.Five different sets of photographs are described inthis standard,designated as Method A(ISO/Swedish Stan-dard2)and Methods B through E(SSPC Guides and ReferencePhotographs3).The methods differ in the depiction of the initi
5、alsurface,in the definition and depiction of the cleaningconditions,and in the number of cleaning methods included.Because of these differences,the specifier should state whichguide to use.1.2 The colored visual surface preparation guides representdifferent conditions of hot-rolled carbon steel befo
6、re and aftersurface preparation.Prior to cleaning,there are four rustgrades,A to D,that cover the range from intact mill scale to100%rusted and pitted steel.The standards then depict theappearance of the initial conditions after cleaning by one ormore methods(for example,dry abrasive blast cleaning)
7、tovarious degrees of thoroughness.In addition,Method Bincludes three painted conditions that contain various degreesof deterioration.The Guide3depicts these conditions aftervarious degrees of dry abrasive blast cleaning.Method Cincludes four rust grades and three painted conditions thatcontain vario
8、us degrees of deterioration.The Guide4depictsthese conditions after various degrees of hand and power toolcleaning.Method D includes two rust grades and four paintedconditions that contain various degrees of deterioration.TheGuide5depicts these conditions after various degrees of waterjetting,with t
9、hree levels of flash rusting.Method E includestwo rust grades.The Guide6depicts these conditions aftervarious degrees of wet abrasive blast cleaning,with threelevels of flash rusting.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-i
10、zation established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 Other Documents:Pictorial Surface Preparation Standards and Guides2,3,4
11、,5,6Surface Cleanliness Definitions3,43.Terminology3.1 Definitions:3.1.1 The cleanliness definitions for the Method A visualsurface preparation standard appear in the text of the pictorial1This practice is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings,Materials,and Applic
12、ations and is the direct responsibility ofSubcommittee D01.46 on Industrial Protective Coatings.The pictorial standards described were prepared by the Swedish CorrosionInstitute and have been jointly approved by ASTM,The Society For ProtectiveCoatings(SSPC)(VIS 1),and the Swedish Standardizing Commi
13、ssion.Current edition approved Nov.1,2021.Published November 2021.Originallyapproved in 1966.Last previous edition approved in 2017 as D2200 17.DOI:10.1520/D2200-17R21.2The pictorial surface preparation standard Method A is available from TheSociety for Protective Coatings(SSPC),800 Trumbull Drive,P
14、ittsburgh,PA15205-4365,http:/www.sspc.org and Sveriges Standardiseringskommission,Box3295,Stockholm 3,Sweden.3The Visual Guide for Method B and surface cleanliness definitions are availablefrom The Society for Protective Coatings(SSPC),800 Trumbull Drive,Pittsburgh,PA 15205-4365,http:/www.sspc.org.4
15、The Visual Guide for Method C and the surface cleanliness definitions areavailable from The Society for Protective Coatings(SSPC),800 Trumbull Drive,Pittsburgh,PA 15205-4365,http:/www.sspc.org.5The Visual Guide for Method D and the surface cleanliness definitions areavailable from The Society for Pr
16、otective Coatings(SSPC),800 Trumbull Drive,Pittsburgh,PA 15205-4365,http:/www.sspc.org.6The Visual Guide for Method E and the surface cleanliness definitions areavailable from The Society for Protective Coatings(SSPC),800 Trumbull Drive,Pittsburgh,PA 15205-4365,http:/www.sspc.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardi