1、Designation:D2063/D2063M10(Reapproved 2018)Standard Test Methods forMeasurement of Torque Retention for Packages withContinuous Thread Closures Using Non-Automated(Manual)Torque Testing Equipment1This standard is issued under the fixed designation D2063/D2063M;the number immediately following the de
2、signation indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These test methods evaluate the tor
3、que retention ofcontinuous thread closures on containers,with matchingfinishes,for predetermined environmental conditions overtime.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;theref
4、ore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.NOTE1The SI unit system is the recommended system.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is t
5、heresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standar
6、d-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D996 Terminology of Packaging and Distribution Envir
7、on-mentsD3198 Test Method for Application and Removal Torque ofThreaded or Lug-Style Closures(Withdrawn 2016)3D3474 Practice for Calibration and Use of Torque MetersUsed in Packaging ApplicationsD4169 Practice for Performance Testing of Shipping Con-tainers and SystemsD4332 Practice for Conditioning
8、 Containers,Packages,orPackaging Components for TestingE41 Terminology Relating to ConditioningE171/E171M Practice for Conditioning and Testing FlexibleBarrier PackagingE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3.Terminology3.1 Definitions:3.1.1
9、For definitions of general packaging and distributionterms,see Terminology D996.3.1.2 For definitions of application torque and removaltorque,see Test Method D3198.3.1.3 For Definitions regarding conditioning,see Terminol-ogy E41.3.2 Definitions of Terms Specific to This Standard:3.2.1 immediate rem
10、oval torqueremoval torque that ismeasured at a stated interval,from 1 to 5 min after closureapplication.3.2.2 torque retentiona comparison between removaltorque at the end of a test period and a predeterminedimmediate removal torque.4.Summary of Test Methods4.1 Test Method A:Static EvaluationAt pred
11、eterminedtime intervals,the removal torques of representative samples ofa container/continuous thread closure system,previouslystored at various environmental conditions,are measured.4.2 Test Method B:Dynamic EvaluationPractice D4169 isused to develop a uniform system of evaluating the ability ofpri
12、mary packages,in the shipping units,to withstand the1These test methods are under the jurisdiction of ASTM Committee F02 onPrimary Barrier Packaging and are the direct responsibility of Subcommittee F02.25on Rigid Container Closure Systems.Current edition approved Sept.1,2018.Published November 2018
13、.Originallyapproved in 1991.Last previous edition approved in 2012 as D2063/D2063M 10(2012).DOI:10.1520/D2063_D2063M-10R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer t
14、o the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accord
15、ance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 distribution environment.At the end
16、 of predetermined distri-bution cycles,the removal torques of representative samples ofa container/continuous thread closure system are measured.5.Significance and Use5.1 This test method allows for the measurement of thetorque retention properties of container/continuous thread clo-sure systems of various designs,materials,and manufacture,and is suitable for packaging development and engineeringevaluation.5.2 This test method can be used for the evaluation ofcontainer/continuous thread closure