1、Designation:D1863/D1863M05(Reapproved 2011)1Standard Specification forMineral Aggregate Used on Built-Up Roofs1This standard is issued under the fixed designation D1863/D1863M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year
2、of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1NOTEUnits information was editorially corrected i
3、n January 2012.1.Scope1.1 This specification covers the quality and grading ofcrushed stone,crushed slag,and water-worn gravel suitable foruse as coarse mineral aggregate on built-up roofs.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The value
4、s stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.2.Referenced Documents2.1 ASTM Standards:2C29/C29M Test Method for Bulk Density(“Unit Weight”)and Void
5、s in AggregateC33 Specification for Concrete AggregatesC117 Test Method for Materials Finer than 75-m(No.200)Sieve in Mineral Aggregates by WashingC136 Test Method for Sieve Analysis of Fine and CoarseAggregatesD75 Practice for Sampling AggregatesD448 Classification for Sizes of Aggregate for Road a
6、ndBridge ConstructionD1864 Test Method for Moisture in MineralAggregate Usedon Built-Up RoofsD1865 Test Method for Hardness of Mineral AggregateUsed on Built-Up RoofsE11 Specification for Woven Wire Test Sieve Cloth and TestSieves3.Materials and Manufacture3.1 Crushed Stone and GravelThe crushed sto
7、ne andgravel at the time of application shall be hard,durable,opaque,and free of clay,loam,sand,or other foreign substances.3.2 Crushed SlagCrushed slag shall be hard,air-cooled,blast-furnace slag,or electric furnace phosphate slag that isfree of sand,clay,or other foreign substances at the time ofa
8、pplication.4.Requirements4.1 The aggregate shall conform to the gradation require-ments specified in Table 1.4.2 The aggregate shall conform to the physical propertiesspecified in Table 2.4.3 Suggested Field Checks:4.3.1 Aggregate shall be free of ice and snow.4.3.2 A handful of aggregate shall not
9、drip water.4.3.3 The aggregate shall be dry and clean enough to adhereto the hot bitumen flood coat when installed.5.Sampling5.1 Sample aggregates received in bulk in accordance withPractice D75.5.2 For aggregates received in bags or small containers,select a number of bags or small containers at ra
10、ndomequivalent to the cube root of the total number in the shipment.6.Test Methods6.1 GradationTest Method C136.6.2 MoistureTest Method D1864.6.3 Unit Mass(Loose)Test Method C29/C29M,utilizingthe shoveling procedure.6.4 DustTest Method C117.6.5 HardnessTest Method D1865.7.Inspection7.1 Inspection of
11、 the material shall be as agreed uponbetween the purchaser and the supplier.1This specification is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.03on Surfacing and Bituminous Materials for Membrane Waterproofing and Buil
12、t-upRoofing.Current edition approved Nov.1,2011.Published January 2012.Originallyapproved in 1961.Last previous edition approved in 2005 as D1863 05.DOI:10.1520/D1863_D1863M-05R11E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org
13、.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 8.Rejection and Rehearing8.1 Failure to conform to any of the requirement
14、s prescribedin this specification shall constitute grounds for rejection.Incase of rejection,the seller shall have the right to re-inspect therejected material and resubmit the lot after removal of thoseitems not conforming to the requirements.The buyer will thenhave the option to inspect the rework
15、ed lot for compliance tospecification.9.Certification9.1 Certification of material shall be as agreed upon be-tween the purchaser and the supplier.10.Keywords10.1 built-up roofs;crushed slag;crushed stone;gravel;mineral aggregateASTM International takes no position respecting the validity of any pat
16、ent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard o