ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:70.34KB ,
资源ID:184066      下载积分:12 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/184066.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_1751_-_04_2013e1.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_1751_-_04_2013e1.pdf

1、Designation:D175104(Reapproved 2013)1Standard Specification forPreformed Expansion Joint Filler for Concrete Paving andStructural Construction(Nonextruding and ResilientBituminous Types)1This standard is issued under the fixed designation D1751;the number immediately following the designation indica

2、tes the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Dep

3、artment of Defense.1NOTEEditorially corrected 5.5 in September 2013.1.Scope1.1 This specification covers preformed expansion jointfiller having relatively little extrusion and substantial recoveryafter release from compression.1.2 The values stated in inch-pound units are to be regardedas standard.T

4、he values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.NOTE1Attention is called to Specification D1752 and to SpecificationD994.2.Referenced Documents2.1 ASTM Standards:2D545 Test Methods for Preformed Expansion Jo

5、int Fillersfor Concrete Construction(Nonextruding and ResilientTypes)D994 Specification for Preformed Expansion Joint Filler forConcrete(Bituminous Type)D1752 Specification for Preformed Sponge Rubber Corkand Recycled PVC Expansion Joint Fillers for ConcretePaving and Structural Construction3.Orderi

6、ng Information3.1 Products conforming to this specification are manufac-tured in sheet form to a range of thicknesses;namely14,38,12,34,and 1 in.Sheet sizes may be 3 or 4 ft in width and standardlength of 10 ft.Purchaser must specify sheet sizes whenordering.3.2 Joint filler in strip form is cut fro

7、m the sheets asmanufactured.When ordering joint filler strips,the purchasermust specify thickness,width,and length;strip widths areavailable from 2 in.in increments of one half inch.4.Material4.1 This product shall consist of preformed sheets or stripsmade from cane or other suitable fibers of a cel

8、lulosic naturesecurely bound together and then uniformly saturated withasphalt;or strips formed from clean granulated cork securelybound together by a suitable asphalt binder and encasedbetween two layers of saturated felt or two layers of glass-fiberfelt.4.2 Preformed strips of expansion joint fill

9、er shall be of suchcharacter as not to be deformed or broken by twisting,bending,or other ordinary handling when exposed to atmosphericconditions.5.Requirements5.1 Test SpecimenThe sample to be tested shall be cutfrom the sheet,as manufactured,and shall be representative ofthe sheet stock.5.2 Compre

10、ssionThe stress required to compress the testspecimen to 50%of its thickness before test shall be not lessthan 100 and not more than 750 psi(689 to 5171 kPa).If thenominal thickness of the specimen is less than12in.(13 mm),a maximum stress of 1250 psi(8618 kPa)will be permitted.The sample after comp

11、ression,shall show a loss of not morethan 3%of its original weight.5.3 ExtrusionTest specimen shall be compressed to 50%of its thickness before test with three of its edges restrained.The amount of extrusion of the free edge shall not exceed 0.25in.(6.4 mm).5.4 RecoveryThe test specimen shall be com

12、pressed to50%of its thickness before test.The load shall be releasedimmediately after application.At the end of 10 min after1This specification is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.34 onPreformed Joint Filler

13、s,Sealers and Sealing Systems.Current edition approved Sept.1,2013.Published November 2013.Originallyapproved in 1983.Last previous edition approved in 2008 as D1751 04(2008).DOI:10.1520/D1751-04R13E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service

14、 at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 release of the applied load,the specimen shall have re

15、coveredto at least 70%of its thickness before test.5.4.1 In case of failure to comply with the aboverequirements,the test specimen shall be given three applica-tions of a load sufficient to compress the material 50%of itsthickness before test.The load shall be released immediatelyafter each applicat

16、ion.At the end of 1 h after the thirdapplication,the specimen shall have recovered to at least 70%of its thickness before test.5.5 DensityFor fiber joint only,oven dry the specimen at220 6 5F(104 6 3C)for 2 h.after oven drying,cool thespecimen to room temperature in a covered desiccator,andweigh to nearest 0.1 g.The density of air dried filler materialshall not be less than 19 lb/cu.ft.(304 kg/cu.m).The densityof oven dried fiber filler shall not be less than 18 lb/cu.ft.(288kg/cu.m).5.6 Water A

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2