1、Designation:C80014Standard Specification forFibrous Glass Blanket Insulation(Aircraft Type)1This standard is issued under the fixed designation C800;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number i
2、n parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers the composition,size,dimensions,and
3、physical properties of glass fiber blanketthermal and acoustical insulation for use up to 700F(370C)in aircraft applications.For specific applications,the maximumtemperature shall be agreed upon between the supplier and thepurchaser.1.2 The values stated in inch-pound units are to be regardedas stan
4、dard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standa
5、rd to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2C167 Test Methods for Thickness and Density of Blanket orBatt Thermal InsulationsC168 Terminology Relating to Thermal InsulationC
6、177 Test Method for Steady-State Heat Flux Measure-ments and Thermal Transmission Properties by Means ofthe Guarded-Hot-Plate ApparatusC390 Practice for Sampling and Acceptance of ThermalInsulation LotsC411 Test Method for Hot-Surface Performance of High-Temperature Thermal InsulationC518 Test Metho
7、d for Steady-State Thermal TransmissionProperties by Means of the Heat Flow Meter ApparatusC552 Specification for Cellular Glass Thermal InsulationC1045 Practice for Calculating Thermal Transmission Prop-erties Under Steady-State ConditionsC1058 Practice for Selecting Temperatures for Evaluatingand
8、Reporting Thermal Properties of Thermal InsulationC1304 Test Method for Assessing the Odor Emission ofThermal Insulation MaterialsC1511 Test Method for Determining the Water Retention(Repellency)Characteristics of Fibrous Glass Insulation(Aircraft Type)C1559 Test Method for Determining Wicking of Fi
9、brousGlass Blanket Insulation(Aircraft Type)D5034 Test Method for Breaking Strength and Elongation ofTextile Fabrics(Grab Test)E691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test MethodF1110 Test Method for Sandwich Corrosion Test2.2 Other Standards14 CFR FAR(Fe
10、deralAviation Regulations)25.853 Appen-dix F,Part I314 CFR FAR(Federal Aviation Regulations)25.856(a)Appendix F,Part IV33.Terminology3.1 DefinitionsTerminology C168 shall be considered asapplying to the terms used in this specification.Definitions inTest Method C552 shall be considered as applying t
11、o theacoustical terms used in this standard.3.2 Definitions of Terms Specific to This Standard:3.2.1 WettingA condition where the water has penetratedinto the insulation and fills the spaces between the fibers.4.Classification4.1 Fibrous glass blanket insulation covered by this speci-fication shall
12、be classified into Types based on temperaturelimits,Classes based on acoustical properties,Grades based onnominal density and Groups based upon thickness as shown inTable 1.4.2 The insulation shall be either water repellent or non-water repellent.1This specification is under the jurisdiction of ASTM
13、 Committee C16 onThermal Insulation and is the direct responsibility of Subcommittee C16.23 onBlanket and Loose Fill Insulation.Current edition approved Feb.1,2014.Published July 2014.Originally approvedin 1975.Last previous edition approved in 2008 as C800 08.DOI:10.1520/C0800-14.2For referenced AS
14、TM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from,National Archives and Records Administration 8601 AdelphiRoad Colleg
15、e Park,MD 20740-6001.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.Ordering Information5.1 The type,class,grade,and group suited to the conditionsof intended service shall be specified by the purchaser afterconsultation with the suppl
16、ier.Type refers to servicetemperature,class refers to thermal/acoustical properties,graderefers to nominal density and group refers to thickness ofinsulation.5.2 It shall also be specified whether the insulation is to bewater repellent or non-water repellent.6.Materials and Manufacture6.1 Composition:6.1.1 Fiber shall be glass processed from a molten state intofibrous form.6.1.2 Binder shall be of a type and quantity to provide theproperties and performance listed in this specification.Addi-tive