1、Designation:D109407(Reapproved 2019)An American National StandardStandard Test Method forWater Reaction of Aviation Fuels1This standard is issued under the fixed designation D1094;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the y
2、ear of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method covers the det
3、ermination of the pres-ence of water-miscible components in aviation gasoline andturbine fuels,and the effect of these components on volumechange and on the fuel-water interface.1.2 The values stated in SI units are to be regarded asstandard.The values given in parentheses after SI units areprovided
4、 for information only and are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the app
5、licability of regulatory limitations prior to use.This standard involves the use of hazardous chemicals identi-fied in Section 7.Before using this standard,refer to supplierssafety labels,Material Safety Data Sheets and other technicalliterature.2.Referenced Documents2.1 ASTM Standards:2D381 Test Me
6、thod for Gum Content in Fuels by Jet Evapo-rationD611 Test Methods for Aniline Point and Mixed AnilinePoint of Petroleum Products and Hydrocarbon SolventsD1836 Specification for Commercial HexanesD2699 Test Method for Research Octane Number of Spark-Ignition Engine FuelD2700 Test Method for Motor Oc
7、tane Number of Spark-Ignition Engine FuelD3948 Test Method for Determining Water Separation Char-acteristics ofAviation Turbine Fuels by Portable Separom-eter2.2 Energy Institute Standard:3IP Standard Test Methods Vol 2,Appendix B,Specificationfor Petroleum Spirits3.Terminology3.1 Definitions of Ter
8、ms Specific to This Standard:3.1.1 film,nthin,translucent layer that does not adhere tothe wall of the glass cylinder.3.1.2 lace,nfibers thicker than hairlike shred or of whichmore than 10%are interlocking,or both.3.1.3 loose lace or slight scum,or both(Table 2,Rating 3),nan assessment that the fuel
9、/buffer solution interface iscovered with more than 10%but less than 50%of lace orscum that does not extend into either of the two layers.3.1.4 scum,nlayer thicker than film or that adheres to thewall of the glass cylinder,or both.3.1.5 shred,nhairlike fibers of which less than 10%areinterlocking.3.
10、1.6 shred,lace or film at interface(Table 2,Rating 2),nan assessment that fuel/buffer solution interface containsmore than 50%clear bubbles or some but less than 10%shred,lace,film or both.3.1.7 tight lace or heavy scum,or both(Table 2,Rating 4),nan assessment that the fuel/buffer solution interface
11、 iscovered with more than 50%of lace or scum,or both,thatextends into either of the two layers or forms an emulsion,orboth.3.1.8 water reaction interface conditions rating,na quali-tative assessment of the tendency of a mixture of water andaviation turbine fuel to form interface films or precipitate
12、s.3.1.9 water reaction separation rating,na qualitativeassessment of the tendency of insufficiently cleaned glasswareto produce emulsions or precipitates,or both,in separated fueland water layers.3.1.10 water reaction volume change,na qualitative indi-cation of the presence in aviation gasoline of w
13、ater-solublecomponents.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricantsand is the direct responsibility ofSubcommittee D02.J0.05 on Fuel Cleanliness.Current edition approved Feb.1,2019.Published February 2019.Originallyapproved in 195
14、0.Last previous edition approved in 2013 as D1094 07(2013).DOI:10.1520/D1094-07R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page on
15、the ASTM website.3Available from Energy Institute,61 New Cavendish St.,London,WIG 7AR,U.K.,http:/www.energyinst.org.uk.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationa
16、lly recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 4.Summary of Test Method4.1 A sample of the fuel is shaken,using a standardizedtechnique,at room temperature with a phosphate buffer solu-tion in scrupulously cleaned glassware.The cleanliness of theglass cylinder is tested.The change in volume of the aqueo