ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:76.75KB ,
资源ID:184752      下载积分:12 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/184752.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_C_1073_-_12.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_C_1073_-_12.pdf

1、Designation:C107312Standard Test Method forHydraulic Activity of Slag Cement by Reaction with Alkali1This standard is issued under the fixed designation C1073;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.

2、A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the rapid determination ofhydraulic activity of slag cement.This test method measuresthe accelerated strength dev

3、elopment of the slag cement byusing sodium hydroxide solution as mixing water and curing atelevated temperature.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety co

4、ncerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.A specific warningstatement is given in Section 6.1.4 The text of this standard ref

5、erences notes and footnoteswhich provide explanatory information.These notes and foot-notes(excluding those in tables)shall not be considered asrequirements of this standard.2.Referenced Documents2.1 ASTM Standards:2C109/C109M Test Method for Compressive Strength ofHydraulic Cement Mortars(Using 2-i

6、n.or 50-mm CubeSpecimens)C125 Terminology Relating to Concrete and Concrete Ag-gregatesC219 Terminology Relating to Hydraulic CementC305 Practice for Mechanical Mixing of Hydraulic CementPastes and Mortars of Plastic ConsistencyC670 Practice for Preparing Precision and Bias Statementsfor Test Method

7、s for Construction MaterialsC778 Specification for SandC989 Specification for Slag Cement for Use in Concrete andMortars3.Terminology3.1 Definitions:3.1.1 Definitions are given in Terminology C125 and C219.3.2 Definitions of Terms Specific to This Standard:3.2.1 slag,ngranulated blast-furnace slag a

8、s defined inTerminology C125 and ground to cement fineness.4.Significance and Use4.1 This test method can be used as a quality-control test forslag production from a single source after adequate correlationwith tests stipulated in Specification C989.4.2 This test method may be used as an evaluation

9、techniquefor slag cement,when an appropriate correlation with variousfinenesses of slag cements from a specific source ground in aspecific laboratory mill has been previously developed.4.3 The hydraulic activity as measured by this test methodon slag cement samples can provide guidance to a manufac-

10、turer as to fineness level required to maintain a certain level ofhydraulic activity.4.4 While this test method is intended primarily as a qualitycontrol test,some studies have shown that the test method iscapable of evaluating the hydraulic activity of slag cementsfrom different sources.5.Apparatus

11、5.1 Three-Gang Molds for 2-in.or 50-mm Cubes andCompression Test Machine,as specified in Test Method C109/C109M(Note 1).NOTE1Silicone grease is recommended for protection of moldsurfaces from the caustic solution in this test.5.2 Mixer,as specified in Method C305.5.3 Curing Chamber,capable of mainta

12、ining a temperatureof air or water bath of 55 6 2C.5.4 Containers,capable of holding one three-cube mold inan essentially vapor-tight condition.If polyethylene or otherplastic bags are used,they shall have a closure of the zip type.If rigid containers are used,they shall have tight sealing covers(No

13、te 2).The acceptability of containers shall be determined1This test method is under the jurisdiction of ASTM Committee C09 onConcrete and Concrete Aggregatesand is the direct responsibility of SubcommitteeC09.27 on Ground Slag.Current edition approved July 15,2012.Published October 2012.Originallyap

14、proved in 1985.Last previous edition approved in 2011 as C107397a(2011).DOI:10.1520/C1073-12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summa

15、ry page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 by measuring the water loss after curing in air or the gain aftercuring in water bath.Water loss shall be less than 15 mL in aircuring or gain less than 5 mL in wa

16、ter-bath curing.NOTE2Plastic boxes designed for household storage of celery with abottom grid have given good service.6.Materials6.1 Graded Standard SandThe sand used for making testspecimens shall be natural silica sand conforming to therequirements for graded standard sand in Specification C778.6.2 Reagent Sodium Hydroxide Solution(20%):6.2.1 Prepare fresh daily using boiled distilled water andreagent grade sodium hydroxide(NaOH).6.2.2 Dissolve 200 g of sodium hydroxide in 1 L of distilledwate

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2