1、Designation:C143913Standard Test Methods forEvaluating Latex and Powder Polymer Modifiers for use inHydraulic Cement Concrete and Mortar1This standard is issued under the fixed designation C1439;the number immediately following the designation indicates the year oforiginal adoption or,in the case of
2、 revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 These test methods provide a means of determining theeffect of adding polymer modifiers to reference
3、 concrete ormortar.1.2 Most sections of ASTM test methods and practices forhydraulic cement mortar and concrete apply to the preparationand testing of specimens made with polymer-modifiers.However,there are some exceptions,most notably curing,thatneed special procedures in order to develop the prope
4、rtiesinherent with polymer-modification.These test methods coverthese exceptions.1.3 For testing polymer-modified mortar and concretespecimens,the procedures in this standard supersede those inthe referenced ASTM test methods and practices.These testmethods are not applicable to dry,packaged mortar
5、andconcrete.1.4 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establ
6、ish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.(WarningFreshhydraulic cementitious mixtures are caustic and may causechemical burns to skin and tissue upon prolonged exposure.2)2.Referenced Documents2.1 ASTM Standards:3C33 Specifi
7、cation for Concrete AggregatesC39/C39M Test Method for Compressive Strength of Cylin-drical Concrete SpecimensC109/C109M Test Method for Compressive Strength ofHydraulic Cement Mortars(Using 2-in.or 50-mm CubeSpecimens)C127 Test Method for Density,Relative Density(SpecificGravity),and Absorption of
8、Coarse AggregateC128 Test Method for Density,Relative Density(SpecificGravity),and Absorption of Fine AggregateC138/C138M Test Method for Density(Unit Weight),Yield,and Air Content(Gravimetric)of ConcreteC143/C143M Test Method for Slump of Hydraulic-CementConcreteC150 Specification for Portland Ceme
9、ntC173/C173M Test Method forAir Content of Freshly MixedConcrete by the Volumetric MethodC185 Test Method for Air Content of Hydraulic CementMortarC192/C192M Practice for Making and Curing Concrete TestSpecimens in the LaboratoryC231 Test Method for Air Content of Freshly Mixed Con-crete by the Pres
10、sure MethodC260 Specification for Air-Entraining Admixtures for Con-creteC305 Practice for Mechanical Mixing of Hydraulic CementPastes and Mortars of Plastic ConsistencyC403/C403M Test Method for Time of Setting of ConcreteMixtures by Penetration ResistanceC494/C494M Specification for Chemical Admix
11、tures forConcreteC778 Specification for SandC1202 Test Method for Electrical Indication of ConcretesAbility to Resist Chloride Ion PenetrationC1404/C1404M Test Method for Bond Strength ofAdhesiveSystems Used With Concrete as Measured by DirectTension(Withdrawn 2010)4C1437 Test Method for Flow of Hyd
12、raulic Cement MortarC1438 Specification for Latex and Powder Polymer Modi-fiers in Hydraulic Cement Concrete and Mortar1These test methods are under the jurisdiction of ASTM Committee C09 onConcrete and ConcreteAggregatesand are the direct responsibility of SubcommitteeC09.44 on Polymer-Modified Con
13、crete and MortarsCurrent edition approved Oct.1,2013.Published October 2013.Originallyapproved in 1999.Last previous edition approved in 2008 as C1439 08a.DOI:10.1520/C1439-13.2Section on Safety Precautions,Manual of Aggregate and Concrete Testing,Annual Book of ASTM Standards,Vol.04.02.3For referen
14、ced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4The last approved version of this historical standard is referenced onwww.ast
15、m.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.Significance and Use3.1 These test methods are used to develop data for com-parison with the requirements of Specific
16、ation C1438.Stan-dardized procedures are used to compare the properties ofspecimens made from test mixtures of polymer-modified con-crete or mortar with the properties of specimens made fromreference mixtures.These test methods are not intended tosimulate job conditions.4.Materials4.1 polymer modifierthe polymer modifier of the requiredtype as furnished by the supplier.4.2 antifoam agentantifoam agent of the type recom-mended by the manufacturer,if one is not incorporated in thepolymer modifier.