1、Designation:C869/C869M11(Reapproved 2016)Standard Specification forFoaming Agents Used in Making Preformed Foam forCellular Concrete1This standard is issued under the fixed designation C869/C869M;the number immediately following the designation indicates the yearof original adoption or,in the case o
2、f revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers foaming agents specificallyformulated for making preformed foam for use
3、in the produc-tion of cellular concrete.1.2 The function of this specification is to provide the meansfor evaluating the performance of a specific foaming agent.This is accomplished by using the foaming agent in making astandard cellular concrete test batch(see Test Method C796)from which test speci
4、mens are cast.Then,significant propertiesof the concrete are determined by tests and compared with therequirements of Section 3.1.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore
5、,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.2.Referenced Documents2.1 ASTM Standards:2C796 Test Method for FoamingAgents for Use in ProducingCellular Concrete Using Preformed Foam3.Performance Requirements3.
6、1 The test batch shall conform to the requirements pre-scribed in Table 1.4.Test Methods4.1 The foaming agent being tested shall be used in makingthe test specimens required.4.2 For each of the properties listed in Table 1,the testprocedure,the number and type of test specimens,and themethod of mold
7、ing,curing,and testing shall be as described inTest Method C796.5.Keywords5.1 cellular concrete;foaming agents1This specification is under the jurisdiction of ASTM Committee C09 onConcrete and Concrete Aggregatesand is the direct responsibility of SubcommitteeC09.23 on Chemical Admixtures.Current ed
8、ition approved July 1,2016.Published August 2016.Originallyapproved in 1977.Last previous edition approved in 2011 as C869/C869M11.DOI:10.1520/C0869_C0869M-11R16.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of A
9、STMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 SUMMARY OF CHANGESCommittee C
10、09 has identified the location of selected changes to this specification since the last issue,C86991(2006),that may impact the use of this specification.(Approved July 1,2011)(1)Revised the standard as a dual units specification andreversed the order of units so that SI units appear first.ASTM Inter
11、national takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirely the
12、ir own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be
13、 addressed to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of theresponsible technical committee,which you may attend.If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards,at
14、 the address shown below.This standard is copyrighted by ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.Individual reprints(single or multiple copies)of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585(phone),
15、610-832-9555(fax),or serviceastm.org(e-mail);or through the ASTM website(www.astm.org).Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center,222Rosewood Drive,Danvers,MA 01923,Tel:(978)646-2600;http:/ 1 Physical RequirementsPropertyRequirementDensityThe
16、density shall satisfy either ofthe following:Density after pumping(see Test MethodC796)640 50 kg/m340 3 lb/ft3Oven dry densityA(see Test Method C796)For Type I cement490 40 kg/m330.4 2.5 lb/ft3For Type III cement470 40 kg/m330 2.5 lb/ft3Compressive Strength(see Test MethodC796),min1.4 MPa200 psiTensile Splitting Strength(see Test MethodC796),min0.17 MPa25 psiWater Absorption(see Test Method C796),max25%by volumeLoss of Air During Pumping(see Test MethodC796),maxB4.5%by volumeAFor this comparison