1、Designation:C59609(Reapproved 2017)Standard Test Method forDrying Shrinkage of Mortar Containing Hydraulic Cement1This standard is issued under the fixed designation C596;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of la
2、st revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method determines the change in length ondrying of mortar bars containing hydraulic cement and gradedstandard sand
3、.1.2 The values stated in SI units are to be regarded asstandard.When combined standards are referenced,the selec-tion of measurement system is at the users discretion subjectto the requirements of the referenced standard.1.3 This standard does not purport to address all of thesafety concerns,if any
4、,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.WarningFreshhydraulic cementitious mixtures are caustic and may causechemical burns to skin and
5、tissue upon prolonged exposure).21.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade O
6、rganization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3C157/C157M Test Method for Length Change of HardenedHydraulic-Cement Mortar and ConcreteC219 Terminology Relating to Hydraulic CementC305 Practice for Mechanical Mixing of Hydraulic CementPastes and Mortar
7、s of Plastic ConsistencyC490/C490M Practice for Use of Apparatus for the Deter-mination of Length Change of Hardened Cement Paste,Mortar,and ConcreteC511 Specification for Mixing Rooms,Moist Cabinets,Moist Rooms,and Water Storage Tanks Used in theTesting of Hydraulic Cements and ConcretesC778 Specif
8、ication for Standard SandC1005 Specification for Reference Masses and Devices forDetermining Mass and Volume for Use in the PhysicalTesting of Hydraulic CementsC1437 Test Method for Flow of Hydraulic Cement MortarE177 Practice for Use of the Terms Precision and Bias inASTM Test Methods3.Terminology3
9、.1 The term“drying shrinkage”is defined as the decreasein length of the test specimen,where the decrease is caused byany factor other than externally applied forces under statedconditions of temperature,relative humidity and evaporationrate in the environment;the term includes the net effect of avar
10、iety of phenomena tending to bring about both increases anddecreases in length during the period in which the testspecimens under consideration are stored in the environmentand in which a number of processes,including hydration of thecement,are taking place at a variety of rates.3.2 Other terms used
11、 in this test method are defined inTerminology C219.4.Significance and Use4.1 This test method establishes a selected set of conditionsof temperature,relative humidity and rate of evaporation of theenvironment to which a mortar specimen of stated compositionshall be subjected for a specified period
12、of time during whichits change in length is determined and designated“dryingshrinkage”.4.2 The drying shrinkage of mortar as determined by thistest method has a linear relation to the drying shrinkage ofconcrete made with the same cement and exposed to the same1This test method is under the jurisdic
13、tion of ASTM Committee C01 on Cementand is the direct responsibility of Subcommittee C01.31 on Volume Change.Current edition approved May 1,2017.Published May 2017.Originallyapproved in 1967.Last previous edition approved in 2009 as C596 091.DOI:10.1520/C0596-09R17.2Section on Safety,Manual of Cemen
14、t Testing,Annual Book of Standards,Vol04.01.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes
15、section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on
16、Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 drying conditions.4Hence this test method may be used whenit is desired to develop data on the effect of a hydraulic cementon the drying shrinkage of concrete made with that cement.5.Apparatus5.1 Weighing Devices and WeightsWeighing devices andweights used in determining the mass of materials for mortarmixtures shall conform to the