1、Designation:D1054 02(Reapproved 2007)Standard Test Method forRubber PropertyResilience Using a Goodyear-HealeyRebound Pendulum1This standard is issued under the fixed designation D1054;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,
2、the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope1.1 This test method covers the de
3、termination of impactresilience and penetration of rubber by means of the Goodyear-Healey rebound pendulum,see Fig.1.1.1.1 The term rubber,used within this method,shall referto those substances classified as thermoplastic elastomers,vulcanized(thermoset)rubber,elastomeric materials,and cel-lular mat
4、erials.1.2 All materials,instruments,or equipment used for thedetermination of mass,force,direction,temperature or dimen-sion shall have traceability to the National Institute for Stan-dards and Technology,or other internationally recognizedorganization parallel in nature.1.3 The values stated in SI
5、 units are to be regarded as thestandard.The values given in parentheses are for informationonly.Many of the stated dimensions in SI are direct conver-sions from the U.S.Customary System to accommodate theinstrumentation,practices and procedures that existed prior tothe Metric Conversion Act of 1975
6、.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Docu
7、ments2.1 ASTM Standards:2D3182 Practice for RubberMaterials,Equipment,andProcedures for Mixing Standard Compounds and Prepar-ing Standard Vulcanized SheetsD3183 Practice for RubberPreparation of Pieces for TestPurposes from ProductsD4483 Practice for Evaluating Precision for Test MethodStandards in
8、the Rubber and Carbon Black ManufacturingIndustriesE145 Specification for Gravity-Convection and Forced-Ventilation Ovens2.2 ASTM Adjuncts:Goodyear-Healey Rebound Pendulum Drawings and PartsList33.Summary of Test Method3.1 Impact ResilienceA freely falling pendulum hammerthat is dropped from a given
9、 height impacts a test specimen,imparting a certain amount of energy.A portion of that energyis returned by the specimen to the pendulum and may bemeasured by the extent to which the pendulum rebounds.Sincethe energy of the pendulum is proportional to the verticalcomponent of the displacement of the
10、 pendulum,it may beexpressed as 1 cos(of the angle of displacement)and impactresilience.RB,is readily determined from the equation.RB 51 2 cos angle of rebound!1 2 cos original angle!3 100(1)3.1.1 The value RB is commonly called percentage rebound.3.2 PenetrationDynamic stiffness is a factor that in
11、flu-ences impact resilience.A convenient index of stiffness is thedepth to which the penetration striker penetrates the testspecimen upon impact.4.Significance and Use4.1 The Goodyear-Healey3rebound pendulum is designedto measure percent resilience of a rubber compound as anindication of hysteretic
12、energy loss that can also be defined bythe relationship between storage modulus and loss modulus.The percent rebound measured is inversely proportional to thehysteretic loss.1This test method is under the jurisdiction of ASTM Committee D11 on Rubberand is the direct responsibility of Subcommittee D1
13、1.14 on Time and Temperature-Dependent Physical Properties.Current edition approved May 1,2007.Published July 2007.Originally approvedin 1949.Last previous edition approved in 2002 as D1054 021.DOI:10.1520/D1054-02R07.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM
14、Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The rebound pendulum is no longer available from the Goodyear Tire andRubber Co.,Process Engineering and System Designs,Dept.109 E,1144 EastMarket
15、Street,Akron,OH 44316.Technical and engineering drawings for itsmanufacture and the reproduction of replacement parts are available at a nominalcost from ASTM International Headquarters.Order Adjunct No.ADJD1054.Original adjunct produced in 2000.1Copyright ASTM International,100 Barr Harbor Drive,PO
16、 Box C700,West Conshohocken,PA 19428-2959,United States.NOTICE:This standard has either been superseded and replaced by a new version or withdrawn.Contact ASTM International(www.astm.org)for the latest information4.2 Deflection is determined by measuring the depth ofpenetration of the rebound ball into the rubber block under test.4.3 Percent resilience and deflection are commonly used inquality control testing of polymers and compounding chemi-cals,especially reinforcing material.5.Apparatus5.1