1、Designation:B399/B399M04(Reapproved 2015)Standard Specification forConcentric-Lay-Stranded Aluminum-Alloy 6201-T81Conductors1This standard is issued under the fixed designation B399/B399M;the number immediately following the designation indicates the yearof original adoption or,in the case of revisi
2、on,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers concentric-lay-strandedconductors,made from round aluminum-alloy 6201-T81(hard:so
3、lution heat-treated,cold worked,and then artificially aged)wires,for use for electrical purposes.These conductors shall beconstructed with a central core surrounded by one or morelayers of helically laid wires(Explanatory Notes 1 and 2).NOTE1The aluminum alloy and temper designations conform toANSI
4、H35.1/H35.1M.Aluminum-alloy 6201 corresponds to UnifiedNumbering System alloy A96201 in accordance with Practice E527.1.2 The values stated in inch-pound units or SI units are tobe regarded separately as standard.The values in each systemare not exact equivalents;therefore,each system shall be usedi
5、ndependently of the other.Combining values from the twosystems may result in nonconformance with the specification.1.2.1 For density,resistivity and temperature,the valuesstated in SI units are to be regarded as standard.2.Referenced Documents2.1 The following documents of the issue in effect on dat
6、eof material purchase form a part of this specification to theextent referenced herein:2.2 ASTM Standards:2B193 Test Method for Resistivity of Electrical ConductorMaterialsB263 Test Method for Determination of Cross-SectionalArea of Stranded ConductorsB354 Terminology Relating to Uninsulated Metalli
7、c Electri-cal ConductorsB398/B398M Specification for Aluminum-Alloy 6201-T81and 6201-T83 Wire for Electrical PurposesB682 Specification for Metric Sizes of Electrical ConductorsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE527 Practice for Numberi
8、ng Metals and Alloys in theUnified Numbering System(UNS)2.3 ANSI Standards:3ANSI H35.1 American National Standard for Alloy andTemper Designation Systems for AluminumANSI H35.1M American National Standard Alloy andTemper Designation Systems for Aluminum Metric2.4 NIST Standards:4NBS Handbook 100 Cop
9、per Wire Tables of the NationalBureau of Standards2.5 Aluminum Association Publication:5Publication 50 Code Words for Overhead Aluminum Elec-trical Conductors3.Classification3.1 For the purpose of this specification,conductors areclassified as follows(Explanatory Notes 1 and 2):3.1.1 Class AAFor bar
10、e conductors usually used in over-head lines.3.1.2 Class AFor conductors to be covered with weather-resistant materials.4.Ordering Information4.1 Orders for material under this specification shall includethe following information:4.1.1 Quantity of each size,stranding,and class,4.1.2 Conductor size,a
11、rea,and aluminum 1350 equivalentsize(if required)(Section 8 and Table 1,Table 2,or Table 3),4.1.3 Number of wires(Table 1,Table 2 or Table 3),4.1.4 Direction of lay of outer layer of aluminum wires ifother than right-hand(see 7.4),4.1.5 Compressed stranding,if required(see 8.2),4.1.6 Special tension
12、 test,if required(see 9.2 and 14.2),4.1.7 Place of inspection(see 15.2),1This specification is under the jurisdiction of ASTM Committee B01 onElectrical Conductors and is the direct responsibility of Subcommittee B01.07 onConductors of Light Metals.Current edition approved April 1,2015.Published Apr
13、il 2015.Originallyapproved in 1963.Last previous edition approved in 2010 as B399/B399M 04(2010).DOI:10.1520/B0399_B0399M-04R15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,re
14、fer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.4Available from National Institute of Standards and Technology(NIST),100Bureau Dr.,Stop 1070,Gaithersburg,MD 20899-10
15、70,http:/www.nist.gov.5Available from Aluminum Association,Inc.,1525 Wilson Blvd.,Suite 600,Arlington,VA 22209,http:/www.aluminum.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.1.8 Special package marking,if required(Section 16),4.
16、1.9 Package size and type(see 16.1),and4.1.10 Heavy wood lagging,if required(see 16.4).5.Requirements of Wires5.1 The aluminum-alloy wire used shall conform to therequirements of Specification B398/B398M.6.Joints6.1 In conductors composed of seven wires,only cold-pressure joints or electric-butt,cold-upset joints are permittedin the six outer finished wires;no joints are permitted in thecenter wire.In other conductors,cold-pressure welds,electric-butt,cold-upset welds,or electric-butt welds may