ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:98KB ,
资源ID:186609      下载积分:8 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/186609.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_B_973_-_10_2014.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_B_973_-_10_2014.pdf

1、Designation:B97310(Reapproved 2014)Standard Specification forTin-Coated Braid and Ribbon Flat Copper Wire intended foruse in Electronic Application1This standard is issued under the fixed designation B973;the number immediately following the designation indicates the year oforiginal adoption or,in t

2、he case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers tin-coated hard-drawn copperbraid and ribbon flat wire intended f

3、or electronic application(Explanatory Note 1).1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.2.1 ExceptionsThe SI values for densit

4、y,resistivity,andvolume are to be regarded as standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of

5、 regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2B1 Specification for Hard-Drawn Copper WireB3 Specification for Soft or Annealed Copper WireB49 Specification for Copper Rod Drawing Stock for Elec-trical PurposesB193 Test Method for Resistivity of Electrical ConductorMa

6、terialsB258 Specification for Nominal Diameters and Cross-SectionalAreas ofAWG Sizes of Solid Round Wires Usedas Electrical Conductors2.2 Other Standards:3NBS Handbook 100 Copper Wire Tables3.Ordering Information3.1 Orders for material under this specification shall includethe following information:

7、3.1.1 Quantity of each size,3.1.2 Wire size-thickness and width in inches(see 5.3),3.1.3 Type of copper,if special(see 4.2),3.1.4 Package size(see 10.1),3.1.5 Special packaging marking,if required,and3.1.6 Place of inspection(see 7.1).4.Material4.1 Tin for CoatingThe tin shall be electroplated for t

8、hecoating and shall be commercially pure(Explanatory Note 1).For purposes of this specification,the tin shall be consideredcommercially pure if the total of other elements,exclusive ofcopper,does not exceed 1%.Not withstanding the previoussentence,chemical analysis of the tin coating or of the tin u

9、sedfor coating shall not be required under this specification.4.2 Copper-Base MetalThe base metal shall be copper ofsuch quality and purity that the finished product shall haveproperties and characteristics prescribed in this specification.NOTE1Specifications B1,B3,or B49 defines copper suitable for

10、 use.5.General Requirements(See Section 8)5.1 Tensile and ElongationThe tin-coated copper flat wirein the hard drawn condition shall conform to elongationrequirements of 1%minimum to 5%maximum.The tensilestrength shall be 55 000 psi(379 MPa)minimum.5.2 Resistivity(Explanatory Note 3)The electrical r

11、esis-tivity of the coated wire at a temperature of 20C shall notexceed the values prescribed in Table 1.5.3 Dimensions and Permissible VariationsThe flat wiresizes shall be expressed as the thickness and width of the wirein decimal fractions of an inch to the nearest 0.0001 in.(0.0025mm).The tin-coa

12、ted flat wire shall not vary from the specifiedthickness and width by more than the amounts specified inTable 2 and Table 3,respectively.5.4 Continuity of CoatingThe tin coating shall be continu-ous.The continuity of coating on the flat wire shall bedetermined on representative samples taken before

13、braiding1This specification is under the jurisdiction of ASTM Committee B01 onElectrical Conductors and is the direct responsibility of Subcommittee B01.04 onConductors of Copper and Copper Alloys.Current edition approved Oct.1,2014.Published October 2014.Originallyapproved in 2010.Last previous edi

14、tion approved in 2010 as B973 10.DOI:10.1520/B0973-10R14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Availabl

15、e from National Technical Information Service(NTIS),5301 ShawneeRd.,Alexandria,VA 22312,http:/www.ntis.gov.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 applications or insulating.The continuity of coating shall bedetermined by the hydr

16、ochloric acid-sodium polysulfide test inaccordance with 6.4.5.5 JointsNecessary joints in the wire and rods prior tofinal coating and drawing shall be made in accordance with thebest commercial practice.There shall be no uncoated joints inthe final product.5.6 FinishThe coating shall consist of a smooth continu-ous layer,firmly adherent to the surface of the copper.The wireshall be free of all imperfections not consistent with the bestcommercial practice.6.Test Methods6.1 Tensile Strength and El

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2