1、Designation:B429/B429M101Standard Specification forAluminum-Alloy Extruded Structural Pipe and Tube1This standard is issued under the fixed designation B429/B429M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the year of last revis
2、ion.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1NOTETable 1 was corrected editorially in February 2012.1.
3、Scope*1.1 This specification covers aluminum-alloy extrudedstructural pipe and tube in those selected alloys shown in Table1 and tempers shown in Table 2,and in those standard sizesshown in Tables 3-5,as well as in other nonstandard sizes asagreed upon between the purchaser and supplier.Such pipe an
4、dtube is intended for use in structural applications such ashighway and bridge rails,chain-link fence posts,handrails,sign structures,awning supports,lighting brackets,etc.Struc-tural pipe and tube is not intended for fluid-carrying applica-tions involving pressure.NOTE1For drawn seamless tube used
5、in pressure applications seeSpecifications B210 and B210M,for seamless pipe and seamless extrudedtube used in pressure applications see Specifications B241/B241M,andfor drawn tube and pipe for general purpose applications see SpecificationB483/B483M.1.2 Alloy and temper designations are in accordanc
6、e withANSI H35.1/H35.1(M).The equivalent Unified NumberingSystem alloy designations are those of Table 1 preceded byA9,for example,A96061 for alloy 6061 in accordance withPractice E527.1.3 For acceptance criteria for inclusion of new aluminumand aluminum alloys in this specification,see Annex A2.1.4
7、 UnitsThe values stated in either inch-pound units orSI units are to be regarded separately as standard.SI units areshown in brackets.The values stated in each system may not beexact equivalents;therefore,each system shall be used inde-pendently of the other.Combining values from the two systemsmay
8、result in non-conformance with the specification.1.4.1 While this standard is a combined SI and inch-poundstandard,standard pipe sizes are not applicable to SI units,therefore non-rationalized SI units(soft conversions)areshown for reader convenience.Rationalized hard convertedSI units are shown in
9、brackets while non-rationalized(softconverted)SI units are shown in parentheses.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determ
10、ine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2B210 Specification for Aluminum and Aluminum-AlloyDrawn Seamless TubesB210M Specification for Aluminum and Aluminum-AlloyDrawn Seamless Tubes(Metric)B241/B241M Specification for Aluminum and Alumi
11、num-Alloy Seamless Pipe and Seamless Extruded TubeB483/B483M Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General PurposeApplicationsB557 Test Methods for Tension Testing Wrought and CastAluminum-and Magnesium-Alloy ProductsB557M Test Methods for Tension Testing Wrough
12、t and CastAluminum-and Magnesium-Alloy Products(Metric)B660 Practices for Packaging/Packing of Aluminum andMagnesium ProductsB666/B666M Practice for Identification Marking of Alumi-num and Magnesium ProductsB807/B807M Practice for Extrusion Press Solution HeatTreatment for Aluminum AlloysB881 Termin
13、ology Relating to Aluminum-and Magnesium-Alloy ProductsB918 Practice for Heat Treatment of Wrought AluminumAlloysB945 Practice for Aluminum Alloy Extrusions Press Cooledfrom an Elevated Temperature Shaping Process for Pro-duction of T1,T2,T5 and T10Type Tempers1This specification is under the jurisd
14、iction of ASTM Committee B07 on LightMetals and Alloys and is the direct responsibility of Subcommittee B07.03 onAluminum Alloy Wrought Products.Current edition approved June 15,2010.Published July 2010.Originallyapproved in 1965.Last previous edition approved in 2006 as B429 06.DOI:10.1520/B0429_B0
15、429M-10.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this s
16、tandardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 E29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE34 Test Methods for Chemical Analysis of Aluminum andAluminum-Base AlloysE527 Practice for Numbering Metals and Alloys in theUnified Numbering System(UNS)E607 Test Method for Atomic Emission SpectrometricAnalysis Aluminum Alloys by the Point to Plane Tech-nique Nitrogen Atmosphere(Wi