ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:64.18KB ,
资源ID:187186      下载积分:11 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/187186.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_A_561_-_08_2014.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_A_561_-_08_2014.pdf

1、Designation:A56108(Reapproved 2014)Standard Practice forMacroetch Testing of Tool Steel Bars1This standard is issued under the fixed designation A561;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number

2、in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This practice for macroetch testing has been found to bea use

3、ful and reliable method for evaluating the quality of toolsteel bars.It is used as a quality control and inspection test toreveal by deep acid etching the macrostructure in specimenscut from bars and to show the presence of such conditions aspipe,cracks,porosity,segregation,or foreign material.Theet

4、ched surface is generally examined visually,but magnifica-tion up to about 10 is occasionally employed.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not con

5、sidered standard.2.Referenced Documents2.1 ASTM Adjuncts:2Six Photomacrographs3.Apparatus3.1 Etching ContainersMacroetching may be performedin a vessel of borosilicate glass,porcelain,corrosion-resistantmetals,or some other acid-resisting material.4.Reagent4.1 Etching ReagentA solution of equal volu

6、mes of con-centrated hydrochloric acid(HCl,sp gr 1.19)and water iscommonly used for macroetching tool steels.This solutionmust be used under a ventilating hood because HCl is volatileand the fumes are corrosive and irritating,although nontoxic.The solution may be reused within limits.With use,thecon

7、centration of dissolved iron and other metals increases andthe acidity of the solution decreases retarding the etchingaction.Spent solution shall be replaced with fresh solution,notreplenished with concentrated acid.5.Sampling5.1 The selection of specimens for macroetch testing mustbe done with care

8、 for interpretations to be of value.5.1.1 Specimens are usually cut from hot-rolled annealedbars,but may be cut from machined or ground bars if the barsare to be finish machined or ground.5.1.2 The specimen should be located at a sufficient distancefrom the end of the bar to avoid end effects.5.1.3

9、For ease in handling,use specimens14to12in.(6.35to 12.7 mm)thick.5.1.4 Cut specimens to expose a transverse section of thebar;however,the test is occasionally performed on a longitu-dinal section.5.1.5 Specimens may be taken from one or both ends of abar.Each bar may be sampled,or a few typical spec

10、imens maybe tested as representative of a large number of bars.6.Specimen Preparation6.1 In all cutting and grinding operations on the specimen,care must be exercised to avoid heating the surface to anexcessively high temperature.Specimens are cut from bars bysawing,machining,abrasive wheel cutting,

11、or other means.Cutting should be controlled to prevent smearing the cut faceand masking the structure.6.1.1 The“as-cut”surface of a specimen may be sufficientlysmooth to reveal the defects for which the examination isconducted.No additional surface preparation may then benecessary.6.1.2 Additional s

12、urface preparation may be required toremove cutting marks and to allow details to be revealed byetching.In such circumstances,machining,grinding,or pol-ishing may be necessary.Generally,the degree of surfacesmoothness required is greater the finer the detail that must beresolved.When the action of t

13、he etchant is drastic,a coarsersurface finish may be used.6.1.3 The surface must be free of adhering grease and oil.There should be no scale or oxide on the surface which will beexamined after etching.7.Procedure7.1 Temperature for MacroetchingEtching characteristicsare influenced markedly by the te

14、mperature of the etchant.1This practice is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloysand is the direct responsibility of SubcommitteeA01.29 on Tool Steels.Current edition approved March 1,2014.Published March 2014.Originallyapproved in 1966.Last previous

15、 edition approved in 2008 as A561 08.DOI:10.1520/A0561-08R14.2Available from ASTM International Headquarters.Order Adjunct No.ADJA0561.Original adjunct produced in 1984.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 Thus,the reagent temp

16、erature should be controlled for mac-roetching if comparative results are desired.Tool steels aregenerally macroetched at about 160F(71C).At thistemperature,the etching reaction is vigorous and solutionlosses through evaporation are not excessive.The solution maybe heated on a gas or electric hot plate,by an acid-proofimmersion heater,or by steam.7.2 Etching TimeThe etching time should be sufficientlylong to completely reveal the structure in the specimen,yetshould not be so long as to develop a

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2